User manual SHARP LC-150M2E

[. . . ] DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. ONLY CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. "Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. " IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV. Model No. : Serial No. : U. S. A. [. . . ] DISPLAY Press. . . . Displays the receiving channel for 10 seconds. Channel indication reduces in size after about 10 seconds. Press again. . . . Returns the sound to the previous level. LCDTV BASIC OPERATION This product is factory set to comply with the TV broadcasting system in the United States. For Brazil, Argentina and Uruguay, set the color system according to the country before using this product by following the table below. The VIDEO INPUT mode is compatible with color systems worldwide and is automatically set. * The World Multi Auto System is compatible with all color systems indicated below. 1 2 3 4 5 6 7 N358 N443 PAL PAL-M PAL-N SECAM PAL-60 Country TV broadcasting system Factory setting of color system TV Video User setting TV U. S. A Canada, Mexico, Latin America Brazil Argentina, Uruguay Color: NTSC TV ch: US ch Color: NTSC TV ch: US ch Color: PAL-M TV ch: US ch Color: PAL-N TV ch: US ch NTSC (N358) US ch NTSC (N358) US ch NTSC (N358) US ch NTSC (N358) US ch World Multi Auto System World Multi Auto System World Multi Auto System World Multi Auto System Not required or N/A Not required or N/A Set color system to PAL-M (see page 21) Set color system to PAL-N (see page 21) 13 LC-150M2E-GBpp01-17 13 00. 11. 8, 9:03 AM BASIC OPERATION (Continued) Turning on POWER Control section of main unit 1 MAIN POWER M On-screen display Slide the MAIN POWER switch, located on the rear side of the main unit to ON. 2 The Power indicator instantaneously changes from red to green and the main unit is turned on. Note: I Input mode indication disappears after several seconds. Notes: Power/Standby indicator Switching TV/VIDEO AV1/AV2/TV Mode 1 POWER MENU CH Turn on the power of the connected video equipment. Press TV/VIDEO and select the applicable input source. The screen displays AV1, AV2 or TV mode at the upper right corner each time TV/VIDEO is pressed. AV1 mode POWER TV/VIDEO 2 TV/VIDEO CH FLASHBACK 1 4 7 2 5 3 DISPLAY 6 9 MUTE 8 0 Note: AV input mode indication remains for 5 seconds. AV1: Video equipment connected to the AV1 input terminals. An S-video input terminal is additionally provided for the AV1 input. If both the S-video terminal and normal video terminals are connected with cables, the Svideo input terminal takes priority. Press MENU to exit. (Pages 20, 21) (Page 22) Notes: I The TINT display only appears when the color system sets N358 or N443 or AUTO in the NTSC mode. I The displayed items differ depending on the setting conditions. I TV mode This product is factory set to comply with the color system (NTSC-N358) in the United States. For Brazil (PALM), Argentina (PAL-N) and Uruguay (PAL-N), set the color system before using this product. I COLOR SYSTEM Set the system to AUTO for normal reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the set. When the picture or sound is not stable, switching to an appropriate system may improve the picture or sound quality. (Page 26) (Pages 2932) (Pages 19, 2325) * The screen indications shown above are larger than actual for easy reading. 17 LC-150M2E-GBpp01-17 17 00. 11. 8, 9:03 AM ADJUSTMENT Adjusting the SLEEP TIMER Settings 1 2 3 4 Press MENU to display the MENU screen. Press CH (])/([) to move the cursor to SLEEP TIMER. Press VOL (+)/() to display SLEEP TIMER screen. (MENU screen) Press VOL (+)/() to set the sleep timer (in minutes). The setting can be set in increment of 30 minutes and in the range between 30 and 120 minutes. The setting is turned off when --- is displayed. (SLEEP TIMER screen) 5 Press MENU to return to the main screen. 18 LC-150M2E-GBpp18-40 18 00. 11. 8, 9:07 AM ADJUSTMENT (Continued) Adjusting the LANGUAGE Settings The language for the ON SCREEN DISPLAY can be ENGLISH, SPANISH or FRENCH. 1 Press MENU to display the MENU screen. (MENU screen) 2 Press CH (])/([) to move the ">" mark to "SETUP". 3 Press VOL (+)/() to display SETUP mode, then press CH (])/([) to move the ">" mark to "LANGUAGE". 4 Press VOL (+)/() to display LANGUAGE change mode. 5 Press CH (])/([) to select "ENGLISH", "SPANISH (ESPAOL)" or "FRENCH (FRANAIS)". 6 Press MENU to exit. 19 LC-150M2E-GBpp18-40 19 00. 11. 8, 9:07 AM ADJUSTMENT (Continued) Adjusting the VIDEO ADJUST Settings 1 Press MENU to display the MENU screen. (MENU screen) 2 Press CH (])/([) to move the cursor to VIDEO ADJUST. 3 Press VOL (+)/() to display the VIDEO ADJUST Menu screen. (VIDEO ADJUST screen) 4 Press CH (])/([) to move the cursor and select the desired adjustment item. [. . . ] The state of the broadcast may also be bad. Make sure the antenna is facing the right direction. Make sure the outside antenna is not disconnected. The picture is not sharp. The picture moves. The picture is doubled or tripled. Make sure the antenna is facing the right direction. There may be reflected electric waves from mountains or buildings. The picture is spotted. There may be interference from automobiles, trains, high voltage lines, neon lights, etc. [. . . ]