User manual SHARP LC-19S7E

[. . . ] 6, 7 Preparing and Using the Remote Control . . 6 Batteries for Remote Control . . . . . . . . . . . . . . . . . . . . . . . 6 Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the sound quality is poor due to a weak signal or other problems during NICAM broadcast reception, set the "OFF" position of the NICAM to change the TV sound to monaural. POWER </> DISPLAY BRIGHT 1 2 3 4 5 Press the MENU to display the MENU screen. Press the ]/[ to select "CH-SETTING". Press the </> to display the CHSETTING menu. Press the ]/[ to select "NICAM". Press the </> to select "OFF". When the NICAM sound is set to the "OFF" position, the TV sound is output in monaural. SLEEP CH-SETTING RETURN POSITION COLOUR SYSTEM SOUND SYSTEM SKIP FINE NICAM IGR [CH15 ] [AUTO ] [I ] [OFF ] [783. 25MHz] [OFF ] [ON ] MENU MENU TV/VIDEO SELECT: ADJUST: EXIT: MENU ]/[ VOL CH (When off position is selected) 15 NICAM [ MPX -/-- Note: s When the NICAM sound is set to the "OFF" position, the MPX button cannot be used to change the audio mode (stereo and bilingual settings). 23 IGR (German stereo system ) BROADCASTS Enables selection of reception mode when receiving an IGR Stereo signal. To let you enjoy IGR broadcasting, this TV receives IGR system stereo and bilingual broadcasts. Stereo POWER DISPLAY (When stereo sound is received) STEREO 49 49 MONO SLEEP BRIGHT MENU TV/VIDEO TV set is receiving a stereo broadcast. · Each time you press the MPX button, the mode switches between STEREO and MONO. When MONO is selected, the TV sound is output in monaural. Bilingual TV set is receiving a bilingual broadcast. · Pressing the MPX button changes the audio mode in the order shown on the right. · Fluorescent lamp may have reached the end of service life. · Make sure the S-Video terminal is free of connections. Reference Pages 7 ­ 11 11 19, 20 ­ 26 Sound Picture There is no picture or sound. Picture There is no picture. There is no picture from AV-IN 1. There is no sound. · Make sure the volume is not set to minimum. · Make sure the sound is not set to mute. 12 12 There is no picture or sound, just noise. · Make sure the antenna cable is properly connected. · Bad reception can be considered. 7 ­ · Make sure the antenna cable is properly connected. · Bad reception can be considered. Picture is not clear. 7 ­ Picture is light or improperly tinted. · Check colour adjustment. (NTSC mode) 19, 20 The picture is too dark. · Check if BRIGHTNESS is set to DARK. · Check CONTRAST and BLACK LEVEL adjustment. · Fluorescent lamp may have reached the end of service life. 21 19, 20 30 Remote control does not work. · Check if batteries in the remote control have sufficient power. [. . . ] M1 VOL CH · · MPX !"#$%&' MPX !"#$%&'()*+, -. ( M1= M2= !MONO= ! !"#) NICAM 49 !M2 -/-- MPX ( !"#$) MONO 49 !" ( !"#$%) NICAM MONO 49 !!" · !"#$%&'( !MPX NICAM MONO !" MONO !"#$%&'()* MONO 49 !" W I= I= !"#3 !"#$%&'()* !"#$%&'()* +, -. /01234!"5 NICAM !"#$%&'()*+, !"#$%&'()NICAM "OFF" !"#$%&'( POWER </> </> DISPLAY BRIGHT 1 2 3 4 5 MENU !MENU !) MENU ]/[ ! [. . . ]