User manual SHARP LC-20B10N

[. . . ] LC-20B10N LCD COLOUR TELEVISION OPERATION MANUAL Printed in Malaysia Printed on post-consumer recycled paper. TINS-C344WJZZ 06P04-MA-NM ENGLISH LC-20B10N OPERATION MANUAL ENGLISH Contents Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Dear SHARP Customer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Instead of pressing MENU for more than 2 seconds, you can set the channel by selecting "CH SETUP" in "SETUP" in the Menu screen. (See page 14. ) 12 Preset (Continued) Presetting the Channels (MANUAL) Setting a channel to a desired TV station Upper control panel 4 3 1, 2, 6 In a weak reception area or under bad reception conditions Upper control panel 4 1, 2, 3, 5 1 2 1 Press MENU (PRESET-1) on the upper part of the LCD TV set for more than 2 seconds to display the AUTO mode screen. Sound System Press MENU (PRESET-1) on the upper part of the LCD TV set for more than 2 seconds to display the AUTO mode screen. Press MENU (PRESET-1) to display the MANUAL mode screen. While the MANUAL mode screen is displayed, press MENU (PRESET-1) for more than 2 seconds. The channel position number remains in green. Adjust for good reception using VOL (­)/(+) (PRESET-2). After finishing the adjustment, press MENU (PRESET-1) to continue channel presetting. 3 4 5 2 Press MENU (PRESET-1) to display the MANUAL mode screen. · Press MENU (PRESET-1) again to change the MANUAL mode as shown below. NOTE · While the MANUAL mode screen is displayed, press MENU (PRESET-1). (The LANGUAGE mode screen will appear. ) AUTO MANUAL LANGUAGE NORMAL SCREEN 3 Select the channel position using Channel Select or CH ( )/( ). Press MENU for more than 2 seconds. 4 Press VOL (­)/(+) (PRESET-2) to locate the channel you want to preset to the position. Search is initiated and when a TV signal is received during the search, the search stops. Repeat steps 3 and 4 above, to preset the channel positions for other broadcasts, etc. 5 6 Press MENU (PRESET-1) twice to return to the normal screen. NOTE · System may not have been set correctly, if noise can be heard or if there is no sound. In such a case, adjust "SOUND SYSTEM". (See page 14. ) 13 Preset (Continued) Channel Setting (AUTO) Selected item POSITION Description The channel position changes to the upper or lower number. AUTO PAL60 B/G I PAL N443 D/K M SECAM N358 COLOUR SYSTEM The mode changes in the following order: SOUND SYSTEM The mode changes in the following order: The mode changes in the following order: OFF ON Channel numbers with a " (RED)" mark on the left are set to skip. To turn off Skip, press Channel Select to select the desired channel, and then set the Skip mode on the CH setup menu to "OFF". The frequency changes to allow fine tuning. The broadcast sound system changes in the following order: OFF (Monaural TV sound) ON (NICAM sound) Stereo system changes in the following order: OFF (Monaural TV sound) ON (A2 sound) SKIP 1 2 3 4 5 Press MENU to display the Menu screen. Press '/" to select "CH SETUP", and press ENTER. Press '/" to select "AUTO", and press ENTER. Press '/" to select "SOUND SYSTEM". Each time you press \/|, the setting for individual items changes as shown in the table on the right. FINE NICAM A2 NOTE · Switching Colour system: Set the system to Auto for normal TV reception. The Auto mode automatically detects the receiving signal system and changes the reception system of the LCD TV set. When the picture or sound is not stable, switching to an appropriate system may improve the picture or sound quality. · When using Fine tuning, the channel number changes from green to yellow. [. . . ] (NTSC mode) 17 The picture is too dark. · Check if "BACKLIGHT" is set to "DARK". · The fluorescent lamp may have reached the end of its service life. 17 17 ­ Remote control does not work. · Check if batteries in the remote control have sufficient power. · Make sure the remote sensor window is not under strong lighting. · External influences such as lightning, static electricity, etc. , may cause improper operation. [. . . ]