User manual SHARP LC-20B2H

[. . . ] LC-13B2H LC-15B2H LC-20B2H LCD COLOUR TELEVISION ENGLISH OPERATION MANUAL M EN U LC-13B2H LC-15B2H LC-20B2H LCD COLOUR TELEVISION ENGLISH OPERATION MANUAL CONTENTS Page DEAR SHARP CUSTOMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3 SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] One-digit and two-digit methods of selection can be used. Follow the procedure shown below to select channels. To select a one-digit channel (e. g. , Channel 5): DISPLAY BRIGHT POWER SLEEP MENU 1 2 CH ( () )/ Press the button. TV/VIDEO VOL CH If "5­" is indicated and the picture does not change, press the -/-button to switch over to the 1-digit again. select mode and press MPX -/-- CHANNEL SELECT To select a two-digit channel (e. g. , Channel 15): 1 2 3 Press the -/-- button to set the 2digit select mode. button. Note: I Complete this procedure within 4 seconds, otherwise the selection will not be made. Changing channels with the CH ( )/( ) on the remote control. Press the CH ( ) and the channels change in the order shown below: 1 2 3 . Press the CH ( ) and the channels change in the order shown below: 3 2 1 0 99 98 . . 12 SELECTING THE MENU ITEMS Selecting a Menu Item · This LCD TV set allows you to adjust the picture and sound, and set the channels and other features using the On Screen Display. Select the desired menu item by following the steps below and then refer to the indicated page for details. SLEEP TIMER menu ----------------- Page 17 SLLEP TIMER RETURN SLEEP TIMER [---REMAIN] POWER </> DISPLAY BRIGHT 1 2 Press the MENU to display the MENU screen. Press the ]/[ to select the desired menu item. · The " " mark moves up or down. · The " " mark indicates the selected menu item. SLEEP MENU MENU TV/VIDEO ]/[ VOL CH SELECT: ADJUST: EXIT: MENU 3 MPX Press the </> to enter. PICTURE menu (TV mode) ---------- Page 18 PICTURE (TV) RETURN CONTRAST [ 30] COLOUR [ 0] BLACK LEVEL [ 0] SHARPNESS [ 0] RED-BLUE [ 0] GREEN [ 0] RESET -/-- MENU SLEEP TIMER PICTURE FEATURE CH-SETTING SELECT: ENTER: EXIT: MENU SELECT: ENTER: EXIT: MENU (AV mode) --------- Page 18 Notes: I The TINT display only appears when the COLOUR SYSTEM sets N358 or N443 in the NTSC mode. I The displayed items differ depending on the setting conditions. I Items in purple cannot be selected. PICTURE (AV1/AV2/CONPONENT) RETURN CONTRAST [ 30] TINT [ 0] COLOUR [ 0] BLACK LEVEL [ 0] SHARPNESS [ 0] RED-BLUE [ 0] GREEN [ 0] COLOUR SYSTEM [AUTO] RESET SELECT: ENTER: EXIT: MENU FEATURE menu --- Page 20 FEATURE RETURN BRIGHTNESS [BRIGHT ] AUTO POWER OFF [OFF ] UPSIDE [NORMAL ] RIGHT/LEFT [NORMAL ] AV2 IN/OUT [IN ] BLUE BACK [ON ] LANGUAGE [ENGLISH] SELECT: ADJUST: EXIT: MENU CH-SETTING menu ---------------- Page 16 CH-SETTING RETURN POSITION COLOUR SYSTEM SOUND SYSTEM SKIP FINE NICAM IGR [CH15 ] [AUTO ] [I ] [OFF ] [783. 25MHz] [ON ] [ON ] SELECT: ADJUST: EXIT: MENU * The screen indications shown above are larger than actual for easy reading. 13 PRESET On-Screen Display Language Selection Upper control panel VOL CH MENU TV/VIDEO I The MENU on the LCD TV set can also be used to select the language. 1 2 PRESET 1 Press the MENU on the upper part of the LCD TV set for more than two seconds to display the PRESET mode screen. Press the MENU twice to display the LANGUAGE select mode screen. Press the MENU again to change the PRESET mode as shown below. AUTO MANUAL LANGUAGE NORMAL SCREEN UHF 471. 25MHz 3 1, 2, 4 2 Note: I Instead pressing the MENU button more than two seconds, you can display the LANGUAGE select mode by selecting FEATURE LANGUAGE on the Menu screen. LANGUAGE ENGLISH 3 4 Press the CH ( )/( ) to select the language you wish to display. Press the MENU to return to the normal screen. SELECT: EXIT: MENU Presetting the Channels (AUTO) VOL CH MENU TV/VIDEO 2 PRESET 1 I Automatically tunes in and presets receivable TV stations. Make sure the antenna cable is properly connected. (Auto mode screen) Sound System UHF 471. 25MHz 2 1 1 2 Press the MENU (PRESET-1) on the upper part of the LCD TV set for more than two seconds. Press the VOL (+)/(­) (PRESET2) on the upper part of the LCD TV set. All the TV stations in your area that can be received by the LCD TV set are automatically preset. The screen shows whatever is on channel 1 when full auto channel preset is finished. When starting the PRESET after setting the SOUND SYSTEM with the MENU button of Remote Control, the SOUND SYSTEM for all channels are stored into memory. Unused channels are automatically skipped. The Preset mode is only available in the TV mode and cannot be operated in the AV mode. POWER DISPLAY SLEEP BRIGHT MENU MENU 3 TV/VIDEO VOL CH Notes: I MPX -/-- I I 14 PRESET (Continued) Presetting the Channels (MANUAL) Upper control panel VOL CH MENU TV/VIDEO 2 PRESET 1 4 3 1, 2, 6 I Setting a channel to a desired TV station: 1 Press the MENU (PRESET-1) on the upper part of the LCD TV set for more than two seconds. 2 Press the MENU (PRESET-1) to display the MANUAL mode screen. [. . . ] Reference Pages 6 ­ 10 10 18, 19 ­ 25 Sound Picture There is no picture or sound. Picture There is no picture. There is no picture from AV-IN 1. There is no sound. · Make sure the volume is not set to minimum. · Make sure the sound is not set to mute. 11 11 There is no picture or sound, just noise. · Make sure the antenna cable is properly connected. · Bad reception can be considered. 6 ­ · Make sure the antenna cable is properly connected. [. . . ]