User manual SHARP LC-32A47E

[. . . ] LC-32A47E LCD COLOUR TELEVISION LCD-FARBFERNSEHGERÄT OPERATION MANUAL BEDIENUNGSANLEITUNG DEUTSCH ENGLISH SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or )5) and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. [. . . ] Make sure no object obstructs the OPC sensor, which could affect its ability to sense surrounding light. Clear Voice This function emphasises speech against background noise for greater clarity. It is not recommended for music sources. Picture adjustments Adjusts the picture to your preference with the following picture settings. Adjustment items Selectable items Backlight Contrast Brightness Colour Tint Sharpness c button The screen dims For less contrast For less brightness For less colour intensity Skin tones become purplish For less sharpness d button The screen brightens For more contrast For more brightness For more colour intensity Skin tones become greenish For more sharpness 8 Menu operations Power Control menu No Signal Off When set to "Enable", the TV will automatically enter standby mode if there is no signal input for 15 minutes. · Five minutes before the TV enters standby mode, the remaining time displays every minute. 1 Go to "MENU" > "Setup" > "Programme Setup". If you have already set the PIN under "Child Lock", enter it here. · See page 10 for setting PIN. 2 NOTE · When a TV programme finishes, this function may not operate. Press a/b to select "Auto Search", "Manual Adjust", "Sort" or "Erase Programme", and then press OK. No Operation Off The TV will automatically enter standby mode if no operations are performed during the time span you set ("30min. " or "3hr. "). · Five minutes before the TV enters standby mode, the remaining time displays every minute. Auto Search You can automatically search for and download TV channels by performing the procedure below. This is the same function as from programme auto search to preset download in "Auto Installation". 1 2 Power Management When set, the TV will automatically enter the standby mode. Item Description · · · · · No power management. If there is no signal input for eight minutes, the TV enters the standby mode. Even if you start using the PC and the signal inputs again, the TV stays in standby mode. The TV turns on again by pressing a on the TV or B on the remote control unit (Page 5). If there is no signal input for eight seconds, the TV enters the standby mode. When you start using the PC and the signal inputs again, the TV turns on. The TV turns on again by pressing a on the TV or B on the remote control unit (Page 5). Off Mode 1 Repeat steps 1 and 2 in Programme Setup. Press c/d to select "Yes", and then press OK. 1 Programme auto search 2 Auto labelling 3 Auto sorting 4 Preset download Mode 2 · · · Manual Adjust You can set some channel items manually. 1 2 3 4 5 Setup menu Auto Installation You can run "Auto Installation" again, even after setting up the preset channels. Repeat steps 1 and 2 in Programme Setup. Press c/d to select "Yes", and then press OK. Press a/b/c/d to select the channel you want to edit, and then press OK. · The selected channel information displays. 1 Go to "MENU" > "Setup" > "Auto Installation". If you have already set the PIN under "Child Lock", enter it here. · See page 10 for setting PIN. Press a/b to select the desired menu item, and then press OK. Press a/b/c/d to select or adjust. NOTE · When you exit "Manual Adjust" in the "Programme Setup" menu, preset download automatically runs if you change information on that menu. 2 3 Press c/d to select "Yes", and then press OK. You can set the language, location of the TV and country the same as in the Initial auto installation. Follow steps 1 to 3 on page 5. Fine You can adjust the frequency to the desired position. NOTE · Adjust while checking the background picture as a reference. · Instead of pressing c/d to adjust the frequency, you can set by directly entering the frequency number of the channel with 0­9 numeric buttons. Programme Setup This section describes how to set up analogue TV channels manually. EXAMPLE · 179. 25 MHz: Press 1 s 7 s 9 s 2 s 5. · 49. 25 MHz: Press 4 s 9 s 2 s 5 s OK. 9 Menu operations Colour sys. Select the optimum colour systems to receive ("AUTO", "PAL", "SECAM"). Erase Programme Channels can be erased individually. Sound sys. (Broadcasting system) Select the optimum sound systems (Broadcasting systems) to receive ("B/G", "D/K", "I"). 1 2 3 4 Label When a TV channel sends its Network Name, the "Auto Installation" detects the information and assigns a name to it. However, you can change channel names individually. 1 2 3 Repeat steps 1 to 4 in Manual Adjust. [. . . ] In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. Following the implementation by member states, private households within the EU states may return their used electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you purchase a similar new one. [. . . ]