User manual SHARP LC-40M450M

[. . . ] Dear SHARP customer LC-32M450M LC-40M550M LCD COLOUR TELEVISION Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of trouble-free operation of your product, please read the Important Safety Precautions carefully before using this product. Important Safety Precautions · Cleaning -- Unplug the AC cord from the AC outlet before cleaning the product. Use a soft damp cloth to clean the product. Do not use liquid cleaners, aerosol cleaners or chemical cloth to clean it, as such materials may damage the product. [. . . ] · 49. 25 MHz: Press 4 s 9 s 2 s 5 s ENTER. 7 8 Menu operation 1 2 3 4 Press MENU and the MENU screen displays. (Picture, Audio, ECO, Setup, Option) Press a/b to select the desired menu item. Press a/b or c/d to select the desired item or adjust the item to the desired level. Press ENTER if necessary. H Advanced Colour temp. (Colour temperature) Adjusts the colour temperature to give the best white image. Selected item High Mid-High Middle Mid-Low Low Description White with bluish tone Audio menu Audio STANDARD Treble Bass Balance SRS TS HD Bass enhancer [ [ [ 0 ] ­15 0 ] ­15 0] L +15 +15 R [Off ] [ On] ECO Setup ECO menu ECO No signal off 4 Power management Setup [Disable] Option No operation off Ecology [Disable] White with reddish tone Reset Picture menu Picture AV mode OPC Backlight Contrast Brightness Colour Tint Sharpness Advanced Reset [ + 8 ] ­16 [ +30 ] [ [ [ [ 0 Audio ECO [ STANDARD] [ Off ] +16 +40 +30 +30 +30 +10 Film mode Automatically detects a film-based source (originally encoded at 24/25 frames/second, depending on the vertical frequency), analyses it then recreates each still film frame for high-definition picture quality. (On, Off) Active contrast Automatically adjusts the contrast of an image according to the scene. (On, Off) 3D-Y/C Provides high quality images with minimal dot crawl and cross colour noise. (On, Off) NOTE H Audio adjustments Selected item Treble Bass Balance c button For weaker treble For weaker bass Decrease audio from the right speaker d button For stronger treble For stronger bass Decrease audio from the left speaker H No signal off You can set the TV to automatically power off in about 15 minutes after the TV goes into a state of receiving no programme signals. (Enable, Disable) · Five minutes before the power shuts down, the remaining time displays every minute. NOTE · When a TV programme finishes, and the TV receives signal input, this function may not operate. 0 ] ­30 0 ] ­30 0 ] ­30 0 ] ­10 H SRS TruSurround (TS) HDTM You can enjoy SRS TruSurround HDTM sound, the same as you were in movie theatre. Using SRS TS HD on the menu screen You can produce SRS TruSurround HDTM effects from the "Audio" setting. Selected item On Description SRS TruSurround HDTM creates a high quality surround sound experience, when watching DVD movies and TV programmes broadcast in surround sound. Outputs the normal sound. H Power management (PC input mode only) You can set the TV to automatically power off when no image is displayed on PC. Selected item Off Mode1 Description · No power management · Factory preset value. · If no signal inputs for approximately 8 minutes, the power shuts down. · Even if you start using the PC and the signal inputs again, the TV stays off. · You can turns on manually by pressing POWER. · If no signal inputs for approximately 8 seconds, the power shuts down. · When you start using the PC and the signal inputs again, the TV turns on automatically. · You can turns on manually by pressing POWER. H OPC (Optical Picture Control) setting You can set the TV to automatically adjust the screen to suitable backlight brightness according to the lighting conditions. Selected item On:Display Description Displays the OPC effect on the screen while adjusting the brightness of the screen. The brightness is fixed at the value set in "Backlight". · 3D-Y/C is not selectable depending on the input signal type. · 3D-Y/C may not operate depending on the input signal type or noisy input signal. Monochrome For viewing images in monochrome. (On, Off) DNR (Digital Noise Reduction) Reduces noise on screen and produces a clearer video image. (Off, High, Low, Auto) NOTE Mode2 Off On Off NOTE · For resetting all Picture adjustment items to factory preset values, press a/b to select "Reset", press ENTER, press c/d to select "Yes", and then press ENTER. H Bass enhancer powered by SRS Labs, Inc. This function allows you to enjoy bass-enhanced sound. Selected item On Off NOTE · Make sure no object obstructs the OPC sensor, which could affect its ability to sense surrounding light. Description Bass enhancer function is on. Outputs the normal sound. H No operation off You can set the TV to automatically power off when no TV operation is performed for more than 3 hours. [. . . ] (See page 9. ) Is the antenna connected properly?(See page 3. ) Is "On" selected in "Audio only"?(See page 12. ) · Sound/Picture is not stable or no Sound/Picture colour noise occur. · No picture. · No sound. [. . . ]