User manual SHARP LC-46LE925RU

[. . . ] Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. ASA DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. [. . . ] It is not recommended for music sources. Setup menu MENU [Setup] Option Setup Auto Installation Programme Setup Power Control menu MENU [Power Control] Power Control [Disable] [Disable] Audio No Signal Off No Operation Off Child Lock Position WSS 4:3 Mode Language [On] [Panorama] [English] [Off (0V)] No Signal Off TV/AV only Supply Voltage Menu Operation: A (page 12) When set to "Enable" the TV will automatically enter the standby mode if there is no signal input for 15 minutes. · Five minutes before the TV enters standby mode, the remaining time displays every minute. Auto Installation TV only You can run Auto Installation again, even after setting up the preset channels. NOTE · When a TV programme finishes, this function may not operate. · This function is not available in DTV mode. 1 2 3 Press MENU and the MENU screen displays. Press a/b to select "Auto Installation", and then press OK. If you have already set the PIN under "Child Lock", enter it here. · See page 17 for setting PIN. No Operation Off TV/DTV/AV only Menu Operation: A (page 12) When set to "Enable" the TV will automatically enter the standby mode if no operations are performed for 3 hours. · Five minutes before the TV enters standby mode, the remaining time displays every minute. 4 5 Press c/d to select "Yes", and then press OK. You can set language and country the same as in the initial auto installation. Follow steps 1 and 2 on page 8. 15 Menu operations Programme Setup TV only 4 5 Press a/b to select the desired menu item, and then press OK. Press a/b/c/d to select or adjust. This section describes how to set up analogue TV channels manually. 1 2 3 NOTE · When you exit Programme Setup "Manual Adjust" menu, preset download automatically runs if you change information on that menu. Press MENU and the MENU screen displays. Press a/b to select "Programme Setup", and then press OK. If you have already set the PIN under "Child Lock", enter it here. · See page 17 for setting PIN. Fine You can adjust the frequency to your desired position. NOTE · Adjust while checking the background picture as a reference. · Instead of pressing c/d to adjust the frequency in step 5 above, you can set by directly entering the frequency number of the channel with 0­9. 4 Press a/b to select "Auto Search", "Manual Adjust", "Sort" or "Erase Programme", and then press OK. Auto Search Manual Adjust Sort Erase Programme No Yes EXAMPLE · 179. 25 MHz: Press 1 s 7 s 9 s 2 s 5. Allow you to reset your PIN to the factory preset "1234". Press c/d to select "Yes", and then press OK. Press a/b/c/d to select the channel you want to move, and then press OK. Press a/b/c/d to move it to the desired position, and then press OK. Repeat steps 3 and 4 until all desired channels are sorted. 1 2 3 4 5 1 2 3 4 Repeat steps 1 to 3 in Changing the PIN. Press a/b to select "Reset", and then press OK. Press c/d to select "Yes", and then press OK. NOTE · As a precautionary measure, make a note of your PIN on the back of this operation manual, cut it out and keep it in a safe place that children cannot reach. · See page 32 for resetting the current PIN to the factory preset "1234" if you lose or forget your PIN. Erase Programme An individual programme can be erased. Input Label You can assign each input source a label you like. 1 2 3 4 5 Repeat steps 1 to 4 in Programme Setup. Press c/d to select "Yes", and then press OK. Press a/b/c/d to select the channel you want to erase, and then press OK. · A message screen pops up. 1 2 3 4 5 6 Press b to select the desired input source. Press MENU and the MENU screen displays. [. . . ] ACHA_ OFTM0 OFTM1 OFTM2 OFTM3 OFTM4 OFTM5 OFTM?DCPG* DCPG? AV MODE SELECTION AVMD0 AVMD1 AVMD2 AVMD3 AVMD4 AVMD5 AVMD? VOLUME VOLM* VOLM? NOTE · If an underbar (_) appears in the parameter column, enter a space. · If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS. Rating table for Child Lock Broadcasted rating Useradjusted rating AGE 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Universal Parental X-rated Broadcasted rating Useradjusted rating -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- X-rated -- -- -- -- Universal Parental Universal Parental X-rated 34 -- -- -- -- -- -- Appendix Specifications Item LCD panel Number of dots Video Colour System TV Function TV-Standard Receiving Channel Analogue Digital VHF/UHF CATV 42o LCD COLOUR TV, Model: LC-42RD2EA, LC-42RD2SA 42o Advanced Super View & BLACK TFT LCD 3, 147, 264 dots (1366 g 768 g 3 dots) PAL/SECAM/NTSC 3. 58/NTSC 4. 43/PAL 60 CCIR (B/G, I, D/K, L, L') DVB-T (2K/8K OFDM) E2­E69ch, F2­F10ch, I21­I69ch, IR A­IR Jch, (Digital: E5­E69ch) Hyper-band, S1­S41ch Auto Preset 99 ch, Auto Label, Auto Sort NICAM/A2 450 cd/m2 60, 000 hours (at Backlight Standard position) H : 176° V : 176° 15W g 2 Ø 70 mm g 2, Ø 20 mm g 2 Antenna input RS-232C EXT 1 EXT 2 EXT 3 EXT 4 EXT 5 EXT 6 C. (Common Interface) OUTPUT Headphones Rear Side UHF/VHF 75q Din type (Analogue & Digital) 9 pin MINI-DIN male connector SCART (AV input, Y/C input, RGB input, TV output) SCART (AV input/output, Y/C input, RGB input, AV Link) S-VIDEO (Y/C input), RCA pin (AV input) RCA pin (AV input) Ø 3. 5 mm jack (Audio input), 15 pin mini D-sub (PC/Component) HDMI, Ø 3. 5 mm jack (Audio input) HDMI EN50221, R206001 RCA pin (Audio) Ø 3. 5 mm jack (Audio output) English/German/French/Italian/Spanish/Dutch/Swedish/Portuguese/Finnish/Turkish/Greek/ Russian/Polish AC 220­240 V, 50 Hz 209 W (0. 9 W Standby) (Method IEC60107) 26. 5 kg (Display only), 29. 5 kg (Display with stand) 0°C to e40°C TV-Tuning System STEREO/BILINGUAL Brightness Backlight life Viewing angles Audio amplifier Speaker Terminals OSD language Power Requirement Power Consumption Weight Operating temperature · As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ]