User manual SHARP LC-46LU630E

[. . . ] Contents 1 Get started TV tour Important Environmental efforts Position the TV Help and support 3 3 6 7 9 10 6 Troubleshooting contact SHARP General TV TV channel Picture Sound HDMI USB Network 48 48 48 48 49 49 50 50 50 2 Use your TV Controls Watch TV Watch a connected device Browse home network Browse AQUOS NET + Rent online video 11 11 12 15 17 18 20 7 Product specifications Power and reception Display and sound Display resolutions Multimedia Connectivity Dimensions Help version 51 51 51 51 52 53 53 54 3 Use more of your TV Enjoy HbbTV View Teletext Set locks and timers View subtitles View TV wallpaper Set universal access Use Link operation 22 22 23 24 25 25 26 27 8 Index 55 4 Set up your TV Settings assistant Picture and sound Channels Menu language Other settings Update software Reinstall the TV 30 30 30 31 34 34 34 35 5 Connect your TV About cables Connect devices Connect more devices Computers and the Internet Common interface 36 36 37 43 45 47 EN 2 TV tour Remote control To open or close the Find menu. In the Find menu, access the channel list. To adjust the volume. Options menus offer convenient settings for TV channels or programmes. To switch TV channels. To return to the previous menu page. To open or close the Menu. In the Menu, access connected devices, picture and sound settings, and other useful features. [. . . ] Select [Setup] > [Channel settings] or [Satellite settings]. Select [Child lock] > [Parental rating]. A message prompts you to enter the child lock code. Enter the child lock code with the Numeric buttons. All programmes above the selected age rating are blocked. For information on child lock codes, see Use more of your TV > Set locks and timers > Child lock (Page 24). Subtitle language You can change the subtitle language on some digital channels. Select [Setup] > [Channel settings] or [Satellite settings] > [Subtitle language]. Select [Primary subtitles] or [Secondary subtitles] for the preferred language. Tip: You can also press OPTIONS > [Subtitle language]. English View TV wallpaper What you can do You can display a default picture as the wallpaper on your TV. You can also load another picture as the wallpaper. If the sleeptimer is off, the wallpaper is displayed for 240 minutes. Otherwise, it is displayed for the duration of the sleeptimer. View subtitles Analogue channels 1. Switch the TV to an analogue TV channel. Enter the three-digit page number of the subtitles page (usually '888'). Subtitles display if available. What you need To use another picture as wallpaper, you need a USB storage device that contains a picture that is less than 1 MB in size. Switch on 1. Note: The wallpaper is displayed for the duration of the sleeptimer. For more information on sleeptimer, see Use more of your TV > Set locks and timers > Sleeptimer (Page 24). Digital channels 1. Select [Subtitles off], [Subtitles on] or [On during mute], then press OK. Note: If MHEG application is activated, subtitles are not displayed. If you select [On during mute], subtitles are displayed only when you press to mute the sound. EN 25 Set TV Wallpaper You can load another picture as wallpaper. Note: Loading a new picture overrides the existing picture. Connect the USB storage device to the TV. [. . . ] There is a picture but the sound quality is poor: Make sure that the sound settings are correctly set. There is a picture but sound comes from one speaker only: Make sure that sound balance is set to the centre. EN 49 English HDMI There are problems with HDMI devices: Note that HDCP (High-bandwidth Digital Content Protection) support can delay the time taken for a TV to display content from a HDMI device. If the TV does not recognise the HDMI device and no picture is displayed, switch the source from one device to another and back again. If there are intermittent sound disruptions, make sure that output settings from the HDMI device are correct. [. . . ]