User manual SHARP LCM3700 COMPLETE OPERATION MANUAL

[. . . ] ENGLISH DEUTSCH LC-M3700 LC-M3710 WIDE LCD MONITOR BREITBILD-LCD-MONITOR MONITEUR GRAND ÉCRAN À CRISTAUX LIQUIDES MONITOR LCD PANORÁMICO FRANÇAIS ESPAÑOL OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO STANDBY/ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE LCD MONITOR This equipment complies with the requirements of Directive 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/ 68/EEG. [. . . ] Setting Enlarge Panel Protection Cover [--] [Off] [Detached] STANDBY/ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE 2 Press or to select "Language", then press ENTER . Power control Setup Control Lock Input Select [AV] Option LCD MONITOR Position Picture Flip Language Input 2 Select ID No. Setting Enlarge Panel Protection Cover [Normal] [English] [Input] [--] [Off] [Detached] 3 Press or language. MENU [ MENU [Setup···Language] to select desired Display language settings. English Deutsch Français Español :Select / RETURN :Back MENU :Exit »The menu screen is now displayed in the language selected. 4 Press screen. MENU to return to normal GB 34 PC Operation PC connection 1 One-to-one connection with a PC . . . . . . . Basic operation Connect with RS-232C cross cable between the PC COM port (RS-232C connector) and the RS232C INPUT terminal on the back of monitor. "Rear view To RS-232C INPUT terminal To COM port "PC Basic Operation RS-232C cross cable 2 Daisy chain connection from a single PC. . . . . . . Advanced operation Connect with RS-232C cross cable between the PC COM port (RS-232C connector) and the RS232C INPUT terminal on the back of monitor. Next, connect RS-232C cross cable to the first monitor's RS-232C OUTPUT terminal and to second monitor's RS-232C INPUT terminal. Connect in the same way to the third and subsequent monitors. Up to about 20 monitors can be connected, depending on the length of RS-232C cables and installation environment. "First monitor "Second monitor PC Operation "PC RS-232C cross cable RS-232C cross cable To COM port To RS-232C INPUT terminal To RS-232C INPUT terminal To RS-232C OUTPUT terminal To RS-232C OUTPUT terminal Communication conditions I Set the RS-232C communication settings on the PC to match the monitor's communication settings. Baud rate: Data length: Parity bit: 9, 600 bps 8 bits None Stop bit: Flow control: 1 bit None 35 GB PC Operation (Continued) Communication procedure Basic operation <Command format> When a command is sent from the PC to the monitor, the monitor operates according to the received command, and sends a response message to the PC. Carriage return code C1 C2 C3 C4 P1 P2 P3 P4 Command field (4 prescribed alphanumerical characters) Parameter field (4 character string comprised of: 0-9, +, ­, space, ?) Example: VOLM0030 POWR 1 (" " indicates a space. ) * Be sure to input 4 characters for the parameter. × VOLM30 VOLM 30( ) (" " indicates a space, " " is the carriage return code (0DH, 0AH or 0DH). ) If a command has "R" listed for "Direction" in the "RS-232C Command table" on page 44, the current value can be returned by using "?" as the parameter. Example: 1If an ID number has not been set: VOLM????From PC to monitor (current volume setting: ?) 30 From monitor to PC (current volume setting: 30) 2If an ID number has been assigned (For example, ID number = 001) VOLM ?PC to monitor (" " indicates a space) 30 001 Monitor to PC (" " indicates a space) <Response code format> I When a command has been executed correctly Carriage return code (0DH, 0AH) O K This is returned when execution of the command is finished. * This is returned when there is no such command, or when the command cannot be used in the current state of the monitor (i. e. video auto-adjustment with video display). * If there is a bad connection between the PC and monitor, or if communication has not been established, nothing is returned (not even ERR). If a command takes some time to execute, WAIT may be returned as the return value. Wait for a moment, and OK or ERR will be returned. New commands cannot be received during this time, even if they are sent. If RS-232C control has been locked with Control lock (see page 52), LOCKED is returned as the returned value. I When a command has not been executed correctly* Carriage return code (0DH, 0AH) E R R I If execution of the command is Carriage return taking some time code (0DH, 0AH) W A I T I If RS-232C is locked Carriage return code (0DH, 0AH) L GB O C K E D 36 PC Operation (Continued) Advanced operation I This section explains commands for daisy chain connection. The basic communication procedure is the same as in the "Basic operation" section. <ID numbers> You can assign a unique ID number to each monitor (see page 54). This allows you to control a particular monitor in a daisy chain of monitors. Up to about 20 monitors can be connected, depending on the length of RS-232C cables and installation environment. You can assign ID numbers either from the menu screen (via remote control or the control buttons on the monitor) or from the PC using RS-232C cable. [Example] PC ID number: 1 ID number: 2 ID number: 3 ID number: 4 If monitors are connected as shown above, you can execute commands like "Set the volume of the monitor with ID 4 to 20". PC Operation When controlling monitors linked in a daisy chain by designating ID numbers, you should basically avoid any duplication of ID numbers. [. . . ] 1 2 Table stand Wall-mount bracket Part name Model name AN-37ST1 AN-37AG1 (As of June 2003) Troubleshooting and Specifications » Additional optional accessories may be available in the near future. When purchasing, please read the newest catalogue for compatibility and check the availability. Mounting precautions Special techniques are required to mount this monitor, so be sure to rely on a specialist for mounting work. The customer should never perform any of this work himself or herself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or handling. 65 GB Appendix 1: PC Compatibility Chart PC (analog) and INPUT3 (RGB) signal input compatibility chart Vertical frequency 43Hz 640 × 400 720 × 400 640 × 480 848 × 480 852 × 480 800 × 600 832 × 624 1024 × 768 1280 × 768 1280 × 1024 1366 × 768 540p 1080i 720p * Interlaced () 50Hz 55Hz 56Hz 60Hz 65Hz 70Hz 72Hz 74. 5Hz 75Hz 80Hz 85Hz PC (digital) signal input compatibility chart × × × × × × × × × × × × × × × » Signal timing is confirmed primarily with VESA standard signals. [. . . ]