User manual SHARP LL-S201A

[. . . ] LL-S201A LCD MONITOR OPERATION MANUAL IMPORTANT: To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product. Model No. : Serial No. : U. S. A. ONLY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. [. . . ] To switch the display, use [Input Select] on the menu screen. (See page 18. ) • If the LCD monitor is turned on when there are input signals from both terminals, the video from the DisplayPort input terminal is displayed. To HDMI output terminal on PC HDMI input terminal Check the orientation of the connector and insert it horizontally as far as it will go. • It is possible to connect the monitor’s HDMI input terminal to a smartphone or similar MHL-compliant device using a commercially available MHL cable. This production incorporates MHL 1. 9 E Connecting Peripheral Equipment nUsing the touch panel To use the touch panel, connect the monitor to a USB port on a PC using the supplied USB cable. Connecting headphones (commercially available) Headphones (commercially available) with a stereo mini plug (φ 3. 5 mm) can be connected to the monitor. φ 3. 5 mm stereo mini plug of commercially available headphones Supplied USB cable To USB port on PC Micro-USB terminal Check the orientation of the connector and insert it horizontally as far as it will go. TIPS Headphone jack • When headphones are connected it will no longer be possible to hear sound from the monitor’s speakers. • Volume can be adjusted using [Volume] on the menu screen. (See page 18. ) • The volume is set to 0 when the monitor is shipped from the factory. Connecting the monitor to a power source Caution • Use only the AC adapter and power cord supplied with the monitor. Connect the monitor to the power outlet using the supplied AC adapter and power cord. Back of monitor For power outlet AC adapter connection terminal Core restraine AC adapter core AC adapter (Supplied) Power cord (Supplied) 2. Push the AC adapter core into the core restrainer. E 10 Installation The monitor can be installed in three different ways. nMounting the monitor on the stand 1. Place the stand on a level surface. Standing position Place the monitor on the supplied stand. Caution • The stand is for use in landscape orientation. It cannot be used for portrait orientation. nAssembling the stand 1. Insert the back into the front. Align the mark () on the front with the edge of the back and insert the back from above. Back Back 2. Set the monitor on the stand. Set the monitor so that the logo in the center is aligned with the circle mark on the stand. Front Logo Front 2. Slide the back across. Slide the back until it clicks into place. Circle mark Back 3. Attach the bottom cover. Align the arrow on the bottom cover so that it points toward the front, and press the projections on the bottom cover into the pocket on the front and back. Front Front pocket Projection Bottom cover Arrow Fixing screws (supplied) Back Back pocket TIPS • The stand and the monitor can be secured with fixing screws. 11 E Installation nDisassembling the stand 1. Remove the bottom cover. Push the tabs in towards the center and pull. Tabs Horizontal position Place the monitor on a table or other level surface. Caution • When using the monitor horizontally, use the horizontal tab in the upright position. 1. Lift up the two tabs on the back of the monitor. Bottom cover 2. Remove the back from the front. Depress the button on the front and slide the back across, then pull the back up. Button Front Back 2. Place the monitor where you want to use it. Pen writing position Place the monitor at an angle on a table or other level surface. 1. Hold the flap by the depression on the back of the monitor and pull the flap up. Caution • Do not exert a large amount of force on the monitor from above. Doing so may damage the tabs. Depression 2. Place the monitor where you want to use it. Caution • Do not exert a large amount of force on the monitor from above. [. . . ] In this situation, perform the operation with the pen and your hand separated farther apart. E 22 Specifications nProduct Specifications Model LCD component Max. colors Pixel pitch Viewing angle Screen active area Plug and play Color adjustment Image quality menu Color temperature LL-S201A 20" Class [19-1/2 inch (49. 5cm) diagonal] TFT LCD (pixels) 1920 x 1080 Approx. 16. 77 million colors 0. 225 mm (H) × 0. 225 mm (V) 178° right/left/up/down (contrast ratio ≥ 10) inch (mm) 17 x 9-9/16 (432 x 243) VESA DDC2B Normal/Pen Writing/Game/Multimedia/User 9000K, 7500K, 6500K, 5000K, and 4200K (With individual RGB adjustment and adjustment reset functions) Input terminals HDMI x 1 (HDMI/MHL) DisplayPort x1 Output terminals Headphones φ3. 5 mm mini stereo jack x 1 Speaker output 1W+1W Touch Panel Touch screen system Capacitive USB (for touch panel x1, microUSB Type B Ver. 1. 1 communication) Maximum touch points 10 points Power requirement AC 100 V - 240 V, 50/60 Hz (when using the supplied AC adapter), DC 19 V Operating temperature 32°F to 95°F (0°C to 35°C) Operating humidity 20% to 80% (no condensation) Power consumption 26 W / 35 W / 0. 5 W (when using the supplied AC adapter) (During normal operation/when MHL charging/during standby) * Dimensions (excluding protrusions) inch (mm) Approx. 18-1/4 (W) x 1 (D) x 10-13/16 (H) (463. 8 x 25. 2 x 274. 8) Weight lbs. [. . . ]