User manual SHARP LL-T15G4 OPERATION MANUAL

[. . . ] LCD Monitor LCD Farbmonitor Moniteur LCD Monitor LCD Monitor LCD LL-T15G4 OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUALE D'USO MANUAL DE FUNCIONAMIENTO Untitled-38 1 2003/09/10, 15:39 Table of Contents/Inhaltsverzeichnis/Table des matières/Indice/Índice Notice for Users in the USA . 103 Untitled-38 2 2003/09/10, 15:39 Notice for Users in the USA IMPORTANT: To aid in reporting in case of loss or theft, please record the monitor's model and serial numbers in the space provided. The numbers are located on the rear of the monitor. Serial No. : WARNING ­ FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B computing equipment. SHARP LCD Color Monitor LL-T15G4-H/LL-T15G4-B This device complies with part 15 of the FCC rules. [. . . ] Press the MENU button 4 times to make the OSD (On Screen Display) Menu disappear. Notes: - In most cases automatic adjustment is sufficient. - It may not be possible to achieve correct adjustment with the first automatic adjustment. In such a case, try repeating the automatic adjustment 2 or 3 times. - If necessary due to any of the following, manual adjustments (p. 17) can be performed after the automatic adjustment. - When further fine adjustment is needed. (When the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When making an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright. ) - When the computer's video input signals are Composite Sync or Sync on Green. (Automatic adjustments may not be possible. ) - Automatic adjustment may not be achieved correctly depending on what is displayed on the screen - moving pictures or the MS-DOS prompt etc. After completing the adjustment, press the computer's [Esc] key to exit the Adjustment Program. Note: - If your computer's display mode is set to 65K colors, you may see the different color levels in each color pattern or the gray scale may look colored. (This is due to the input signal specification and is not a malfunction. ) 16 Untitled-40 16 2003/09/10, 15:41 Adjusting the screen display (When using an analog signal) English English Español Italiano Français Deutsch Manual screen adjustment Adjustments can be made using OSD (On Screen Display) Menu provided. Display an image that makes the entire screen very bright. If using Windows, you can open and use the Adjustment Pattern on the accompanying Utility Disk. The ADJUSTMENT Menu will be displayed. ADJUSTMENT MANUAL CLOCK PHASE H-POS V-POS 127 30 200 29 AUTO ADJUSTMENT Menu ADJUSTMENT MANUAL CLOCK PHASE H-POS V-POS 127 30 200 29 AUTO 1024x768 ANALOG V : 6 0Hz H : 4 8. 4kHz MANUAL: Individual menu options are manually adjusted. AUTO: Every menu option is automatically adjusted. Notes: - Press the button to select [AUTO]. - To choose a menu option: / MODE button - To go to the next menu: MENU button CLOCK The figure below demonstrates how to adjust so that vertical flicker noise is not emitted. ( buttons) 1024x768 ANALOG V : 6 0Hz H : 4 8. 4kHz At this point relevant menu options can be adjusted. Each time the MENU button is pressed the next menu is selected. (ADJUSTMENT GAIN CONTROL WHITE BALANCE MODE SELECT OSD Menu disappears) Notes: - The OSD Menu automatically disappears approximately 30 seconds after the last command. - This explanation is based on using the Adjustment Pattern (for Windows) to make adjustments. Vertical flicker noise PHASE The figure below demonstrates how to adjust so that horizontal flicker noise is not emitted. ( buttons) Note: - Adjustments to [PHASE] should be made only after [CLOCK] has been correctly set. Horizontal flicker noise H-POS (horizontal positioning) and V-POS (vertical positioning) To center the Adjustment Pattern within the boundaries of the screen, adjust the left-right (HPOS) values and the up-down (V-POS) values. [. . . ] - When using an ICC profile, set [DISPLAY MODE] to either [STD] or [OFFICE], and set [WHITE BALANCE] to [STD]. 28 Untitled-40 28 2003/09/10, 15:41 Information about the ColorSync profile (For MacOS) About the ColorSync profile ColorSync is Apple Computer's color management system and enables color reproduction characteristics to be realized when used with a compatible application. A ColorSync profile describes the color characteristics of the LCD monitor. Notes: - This monitor's ColorSync profile works with MacOS 8. 5 or above. - When using the ColorSync profile, set [DISPLAY MODE] to either [STD] or [OFFICE], and set [WHITE BALANCE] to [STD]. Setting up the ColorSync profile Notes: - It is necessary to have PC Exchange or File Exchange installed in your system. [. . . ]