User manual SHARP LL-T2015 OPERATION MANUAL

[. . . ] LCD Monitor LCD Farbmonitor Moniteur LCD Monitor LCD Monitor LCD LL-T2015 OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUALE D'USO MANUAL DE FUNCIONAMIENTO Table of Contents/Inhaltsverzeichnis/Table des matières/Indice/Índice Notice for Users in the USA . 129 Notice for Users in the USA IMPORTANT: To aid in reporting in case of loss or theft, please record the monitor's model and serial numbers in the space provided. The numbers are located on the rear of the monitor. Model No. : Serial No. : FCC Statement WARNING ­ FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. [. . . ] (This is due to the specification of the input signal and is not a malfunction. ) 20 Adjusting the screen display (With analog connection) English English Español Italiano Français Deutsch Manual screen adjustment Adjustments can be made using OSD (On Screen Display) Menu provided. ADJUSTMENT Menu ADJUSTMENT MANUAL CLOCK PHASE H-POS V-POS 127 0 250 48 - AUTO + - + - + On Screen Display for adjustment If you are using Windows, open the Adjustment Pattern on the accompanying CD-ROM. (p. 20) If your system is not Windows, you can not use the Adjustment Pattern. Therefore display an image that makes the entire screen light and adjust it through checking visually its actual tone. This chapter provides the procedure how to adjust the screen by using Adjustment Pattern (for Windows). - + INPUT-1 ANALOG 1600 x 1200 V:60Hz H:75. 0kHz MANUAL: Individual menu options are manually adjusted. AUTO: Every menu option is automatically adjusted. Notes: - Press the button to select [AUTO]. - To choose a menu option: / MODE button - To go to the next menu: MENU button CLOCK The figure below demonstrates how to adjust so that buttons) vertical flicker noise is not emitted. The ADJUSTMENT Menu will be displayed. ADJUSTMENT MANUAL CLOCK PHASE H-POS V-POS 127 0 250 48 - AUTO + - + - + - + INPUT-1 ANALOG 1600 x 1200 V:60Hz H:75. 0kHz At this point, relevant menu options can be adjusted. Each time the MENU button is pressed the next menu is selected. (ADJUSTMENT GAIN CONTROL COLOR CONTROL MODE SELECT-1 MODE SELECT-2 OSD Menu disappears) Note: - The OSD Menu automatically disappears approximately 30 seconds after the last command. Vertical flicker noise PHASE The figure below demonstrates how to adjust so that horizontal flicker noise is not emitted. ( buttons) Note: - Adjustments to [PHASE] should be made only after [CLOCK] has been correctly set. Horizontal flicker noise H-POS (horizontal positioning) and V-POS (vertical positioning) To center the Adjustment Pattern within the boundaries of the screen, adjust the left-right (HPOS) values and the up-down (V-POS) values. ( buttons) Screen frame Adjustment Pattern 21 Adjusting the screen display (With analog connection) GAIN CONTROL Menu GAIN CONTROL MANUAL BLACK LEVEL CONTRAST 50 50 - COLOR CONTROL Menu COLOR CONTROL WHITE BALANCE GAMMA + + AUTO 0 - + - INPUT-1 ANALOG 1600 x 1200 V:60Hz H:75. 0kHz INPUT-1 ANALOG 1600 x 1200 V:60Hz H:75. 0kHz MANUAL: Individual menu options are manually adjusted. AUTO: Every menu option is automatically adjusted using the Auto Gain Control* function. Notes: - Press the button to select [AUTO]. - To choose a menu option: / MODE button - To go to the next menu: MENU button * Auto Gain Control function - The Auto Gain Control adjusts contrast and black level based on the brightest and darkest colors of the image displayed. If you are not using the Adjustment Pattern it is necessary to have black area and white area of at least 5 mm x 5 mm on the screen. Adjustment may not be possible without those areas. - If the signal coming from the computer is Composite Sync or Sync on Green, automatic adjustment cannot be performed. Please perform manual adjustment instead. - If [OUT OF ADJUST] is displayed, perform manual adjustment. BLACK LEVEL Total screen brightness can be adjusted while buttons) watching the color pattern. ( Color pattern Notes: - To choose a menu option: / MODE button - To go to the next menu: MENU button WHITE BALANCE After selecting [WHITE BALANCE], press the button and display the adjustment menu. WHITE BALANCE COOL STD WARM USER R-CONTRAST G-CONTRAST B-CONTRAST OK. . . <MENU> Notes: - On settings other than [STD] not all gradations can be displayed. [. . . ] A ColorSync profile describes the color characteristics of the LCD monitor. Notes: - This monitor's ColorSync profile works with MacOS 8. 5 or above. - When using the ColorSync profile, set as follows: - [DISPLAY MODE] [WHITE BALANCE]: [STD] - [GAMMA]: [0] Setting up the ColorSync profile Notes: - It is necessary to have PC Exchange or File Exchange installed in your system. - Depending on the type of computer or OS, command names and methods may differ. [. . . ]