User manual SHARP MD-M1

[. . . ] MD MICRO SYSTEM OPERATION MANUAL MODEL MD-M1 Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. MD-M1 MD micro system consisting of MD-M1 (main unit) and CP-M1 (speaker system). Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] (pages 18 - 19. ) 2 Load a recordable MiniDisc. 3 Press the q REC button. q The unit will enter the recording stand-by mode. 4 Check the recordable time by pressing the DISPLAY button. Note: q Before recording an AM broadcast, enter the recording stand-by mode, and then separate the AM loop antenna from the main unit. Adjust it so that the AM broadcast can be tuned in most clearly. q During recording, you cannot change the station. 5 Press the 0 6 button. 23 EDITING s What the editing function can do You can create original discs using the MD editing function, on which you can change the order of the tracks and you can create disc or track names. q Playback-only MiniDiscs cannot be edited. DIVIDE A single track can be divided into two at any desired position. q The numbers of the tracks which come after the newly divided track will be automatically increased by one. 1 2 3 TRACK/DISC NAME Discs and tracks (up to 255 tracks per disc) can be named. Since track names are displayed when the beginning of each track is located or during playback, you can quickly check the name of each track. q Capital letters, numbers and symbols can be used. (Pages 25, 26) A 1 2 B 3 C D 4 s Type of characters used Type of characters Characters (Symbols) ABCDEFGH I J KL MNOPQ A B C D (Page 28) Capital letters RS T UVWXYZ 1 ( 2 ) 3 4 + 5 , 6 7 . " # $ %& ' COMBINE Two consecutive tracks can be combined into one track. q The numbers assigned to the tracks following the combined tracks will be decreased by one automatically. 1 2 3 4 Symbols ?@< = > _ Number of characters you can enter q Disc names and track names Up to 40 characters (including spaces) can be entered for each name. If more than 40 characters are entered, "NAME FULL" will appear. q Total number of characters per MiniDisc A total of approximately 1, 700 characters can be used for all of the disc and track names. If more than 1, 700 characters are entered, " TOC FULL " will appear. While editing, the "TOC" indicator is displayed. This means the edit results have not been recorded on the MiniDisc. To record the results, select another input or set the unit to the stand-by mode. During writing, the "TOC" goes out, all editing changes have been recorded to the disc. Note: q Storing the edited contents on the disc can be done after several pieces of editing have been finished. A 1 B 2 3 C D A B C D (Pages 28, 29) ERASE/ALL ERASE Tracks you want to erase can be erased one at a time or all at once. q Once a track has been erased, it cannot be recovered. Double-check the track number before erasing it. 1 2 3 4 5 A 1 2 B C 3 D 4 E A B D E (Page 30) MOVE A designated track can be moved to any desired position. q The numbers assigned to the tracks following the track which is moved will be adjusted automatically. 1 2 3 4 A 1 2 B 3 C 4 D C A B D (Page 29) 24 (Continued) s To create a disc name A name for the whole disc. Disc names are displayed when an MD is inserted. (Remote control operation) REC SLEEP 5 Select the character you want pressing the or button. REC SLEEP NAME/ TOC EDIT DISPLAY ENTER / CLEAR 6 Press the ENTER button to enter the character. REC SLEEP q Repeat steps 4 to 6 above to enter the characters in the name. When the next character's type is the same as the previous character, step 4 can be skipped. 7 After entering all of the characters in the name, press the NAME/TOC EDIT button. 1 Press the s button after pressing the MD button. q The total number of tracks and the total playing time on an MD will appear. q The disc name will be recorded. REC SLEEP 2 Press the NAME/TOC EDIT button, and then select "DISC NAME" pressing the button. DISC TOC TRACK TOTAL REMAIN REC SLEEP To erase a disc name: or 1 2 After performing steps 1 to 3. [. . . ] peak) q Amplifier section Output power: FTC 16 watts per channel minimum RMS into 4 ohms from 80 Hz to 20 kHz with no more than 10% total harmonic distortion Output terminals: Speaker; 4 ohms Headphones; 16 - 50 ohms (recommended 32 ohms) Input terminals: AUX; 500 mV/47 k ohms Signal/noise ratio: 95 dB (1 kHz) q MiniDisc recorder section Type: MiniDisc recorder Signal readout: Rotation speed: Error correction: Non-contact, 3-beam semiconductor laser pickup 400 - 900 rpm CLV, Approx. ACIRC (Advanced Cross Interleave Reed-Solomon Code) 20-bit linear (A/D converter) ATRAC (Adaptive TRansform Acoustic Coding) 44. 1 kHz Magnetic modulation overwrite method 20 - 20, 000 Hz 1-bit D/A converter Unmeasurable (less than 0. 001% W. peak) 90 dB (1 kHz) Stereo; 2 channels Monaural; 1 channel (playback only) (long-time recording mode) q Tuner section Frequency range: FM; 87. 5 - 108. 0 MHz AM; 530 - 1, 720 kHz Sensitivity: FM; 2. 5 µV (75 ohms unbalanced) AM; 650 µV/m q Speaker section Type: Full range speaker system Speakers: Maximum input power: Rated input power: Impedance: Dimensions: 4" (10cm) full-range speaker 40 W 20 W 4 ohms Width; 6-5/16" (160 mm) Height; 9-1/2" (240 mm) Depth; 7-1/4" (183 mm) Weight; 4. 0 lbs. (1. 8 kg)/each Quantization: Coding: Sampling frequency: Recording method: Frequency response: D/A converter: Wow and flutter: Signal/noise ratio: 95 dB (1 kHz) Dynamic range: Audio channel: 41 MEMO 42 CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. [. . . ]