User manual SHARP MD-MT200H

[. . . ] PORTABLER MINI-DISC RECORDER LECTEUR-ENREGISTREUR MINIDISC PORTABLE REGISTRATORE DI MINIDISCHI PORTATILE DRAAGBARE MINIDISC RECORDER PORTABLE MINIDISC RECORDER MODELL MODEL MODÈLE MODEL MODELLO MD-MT200H DEUTSCH BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING OPERATION MANUAL FRANÇAIS ITALIANO ······ Siehe Seiten i bis vi und D-1 bis D-44. ······ Se reporter aux pages i à vi et F-1 à F-44. ······ Leggere le pagine i a vi e I-1 a I-44. NEDERLANDS ······ Raadpleeg de bladzijden i t/m vi en N-1 t/m N-44. ENGLISH ······ Please refer to pages i to vi and E-1 to E-44. for SEEG TINSZ0706AWZZ BESONDERE ANMERKUNGEN REMARQUES SPÉCIALES NOTE PARTICOLARI BIJZONDERE OPMERKINGEN SPECIAL NOTES G Audio-visuelles Material kann Urheberrechte umfassen, die ohne Genehmigung des Eigentümers dieser Urheberrechte nicht aufgenommen werden dürfen. [. . . ] (The operation may vary depending on the unit. ) Tracks recorded in monaural cannot be played if equipment does not support the monaural playback. ENGLISH About the recording mode You can select the recording mode from stereo recording, 2 times long recording, 4 times long recording, and monaural recording. Recordable time varies depending on the recording mode. If the tracks are recorded on an 80minute MiniDisc, its recording time changes as follows: Indication SP LP2 LP4 MONO Recording mode Stereo 2 times long (stereo) 4 times long (stereo) Monaural Recording time MAX. 160 min. Useful Features -Advanced Recording- About ATRAC The ATRAC (Adaptive TRansform Acoustic Coding) system compresses the sound data into 1/5 by cutting out the inaudible sound. Since the sound is selected based on psychoacoustics masking, the sound quality is not impaired. This unit is equipped with the ATRAC3 compressing system that can reduce the sound data to 1/10 or 1/20 of its original size. By employing this system, 2 times and 4 times long recordings are enabled in stereo mode. Caution for 4 times long recording (LP4) Special compressing method allows the 4 times long recording to realise long-time stereo recording. Therefore, some noise is recorded occasionally. If sound quality should be emphasised, stereo recording or 2 times long recording is recommended. E-19 01/11/21 MD-MT200H(SEEG)_E_4. fm MD-MT200H ENGLISH Playback sound-actuated recording Recording automatically starts or pauses by detecting sound from the stereo system (Synchronised recording). 4 5 6 7 8 9 Press the PAUSE button on the stereo system to enter the playback pause mode. Select the starting point for your recording and press the PAUSE button. Press the MENU/CHRG button repeatedly to select "REC MODE". Select the recording mode (step 3, page 18) and press the ENTER/SYNC button. The mode will be set automatically after 7 seconds even if the ENTER/SYNC button is not pressed. To cancel the operation, press the :OFF/HOLD button. Recording will begin automatically. Useful Features 1 2 3 Press the REC button. Begin playback on the stereo system connected to this portable MD. Press the REC LEVEL or button to adjust the recording level (see page 11). To interrupt recording When the stereo system is stopped, the unit will enter the synchro recording pause mode. When playback is resumed, the recording will be resumed. If a silence lasts for 3 seconds or more, the recording will be paused (pause function does not work for approximately 10 seconds after a recording starts). When the unit receives sound again, recording automatically starts. A new track number is created when the recording resumes. E-20 01/11/21 MD-MT200H(SEEG)_E_4. fm -Advanced Recording- MD-MT200H Advanced Recording (continued) ENGLISH To start recording from the middle of a track You can erase a portion of a track and make a new recording. All of the tracks that follow the newly recorded track will be erased. 1 2 During playback, press the button at the point where you want to begin recording. [. . . ] If the plugs or sockets are dirty, noise may be heard. Cleaning will prevent noise. Moisture condensation When the unit has condensation inside, the disc signals cannot be read, and the unit may not function properly. In the following cases, condensation may form inside the unit. When the unit is placed in a room where there is excessive steam or moisture. [. . . ]