User manual SHARP MD-E9000

[. . . ] MD COMPACT COMPONENT SYSTEM MODEL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. MD-E9000H MD Compact Component System consisting of MD-E9000H (main unit) and CP-E9000H (speaker system). MD-E9000H OPERATION MANUAL If you require any advice or assistance regarding your Sharp product, please visit our website www. sharp. co. uk/support. [. . . ] Press the 5/3 or 2/4 button to check whether the names are correct. If you find a wrong name while receiving the station, wait until the correct name will be displayed. Press the MEMORY/ENTER button whilst the preset channel number is flashing. (Within 5 seconds) q The new station name has been stored in memory correctly. Notes: q The same station name can be stored in different channels. q In a certain area or during certain time periods, the station names may temporarily be different. 3. After scanning, the number of stations stored in memory will be displayed for 4 seconds. 26 *MD9000H-E24-30 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 26 2001. 4. 20, 2:11 AM Using the Radio Data System (RDS) (continued) s To recall stations in memory To specify programmed types and select stations (PTY search): You can search a station by specifying the programme type (news, sports, traffic programme, etc. see page 25) from the stations in memory. Notes: q If the display has stopped flashing, start again from step 2. If the unit finds out a desired programme type, corresponding channel number and frequency will flash for about 2 seconds, and then the station name will flash for 7 seconds and remain lit. q If you want to listen to the same programmed type of another station, press the PTY. TI button whilst the channel number or station name is flashing. The unit will look for the next station. q If no station can be found, "NOT FOUND" will appear for 4 seconds. MD-E9000H 1 2 1 2 Press the TUNER (BAND) button repeatedly to select "FM". TI button. 3 "PTY TI" and "SELECT" appear alternately. If you select the traffic programme (TP) in step 3, "TP" will appear. (This does not mean that you can listen to the traffic information at that time. ) When a traffic information is broadcast, "TA" will appear. - Using the Radio Data System (RDS) - If you select the traffic programme: 4 5 3 RDS Radio Within 4 seconds, press the 5/3 or 2/4 button to select the programme type. 6 7 Each time the button is pressed, the programme type will appear. If the button is held down for more than 0. 5 seconds, the programme type will appear continuously. 8 4 Whilst the selected programme type is flashing (within 4 seconds), press the PTY. TI button again. 9 10 After the selected programme type has been lit for 2 seconds, "SEARCH" will appear, and the search operation will start. 11 12 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 27 *MD9000H-E24-30 27 2001. 4. 20, 2:11 AM Using the Radio Data System (RDS) (continued) s To automatically play the desired programme (EON-PTY) When the desired type of programme is broadcast, the radio switches to it automatically. 5 When the specified programme starts on an ON (other network) station, the unit will automatically switch to the station and "PTY" will flash. 1 - Using the Radio Data System (RDS) - Tune in to an RDS station (when a station name is displayed). 6 2 Press the EON button when "EON" appears. When the programme is over, the unit will automatically return to the original station. Checking the stand-by mode setting: When in the EON stand-by mode, press the EON button. ("Programme type" ¡ "WAITING") RDS Radio q "PTY TI" will flash for about 4 seconds. q If the EON button is pressed when "EON" is not displayed, "NO EON" will To cancel the EON stand-by mode: When in the EON stand-by mode, press the EON button. ("PTY" will go out. ) appear for 4 seconds to indicate that the unit cannot enter the EON standby mode. 3 Whilst they are displayed, select the desired programme type by pressing the 5/3 or 2/4 button. The selected programme type will flash. 4 Within 4 seconds, press the PTY. TI button. q The selected programme type and "WAITING" will be displayed for 2 seconds each. [. . . ] Your unit checks whether there is a disc inside the unit when the compartment is closed. "NO DISC" appears if no disc is left. Then, set the unit to the power stand-by mode. Carrying the unit with discs left inside can damage it. 48 *MD9000H-E44-48 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 48 2001. 4. 20, 2:16 AM Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ]