User manual SHARP MD-E9000H

[. . . ] MD KOMPAKT KOMPONENTEN SYSTEM CHAÎNE COMPACTE MD SISTEMA COMPACTO MD MD KOMPAKT KOMPONENTSYSTEM SISTEMA COMPACT MD MD COMPACT COMPONENTENSYSTEEM MD COMPACT COMPONENT SYSTEM MODELL MODÈLE MODELO MODELL MODELLO MODEL MODEL MD Kompakt Komponenten System MD-E9000H besteht aus MD-E9000H (Hauptgerät) und CP-E9000H (Lautsprechersystem). Chaîne compacte MD MD-E9000H composé de MD-E9000H (appareil principal) et de CP-E9000H (enceintes acoustiques). Sistema compacto MD MD-E9000H que consta de MD-E9000H (aparato principal) y CP-E9000H (sistema de altavoces). MD-E9000H MD Kompakt Kompontsystem av MD-E9000H (huvudenhet) och CP-E9000H (högtalarsystem). [. . . ] When the TUNING button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: q This can be operated by using the remote control only. q When radio interference occurs, auto scan tuning may stop automatically at that point. q Auto scan tuning will skip weak signal stations. q To stop the auto tuning, press the TUNING button on the remote control again. q When an RDS (Radio Data System) station is tuned in, the frequency will be displayed first, and then the RDS indicator will light. q Full auto tuning can be achieved for RDS stations (see "ASPM" on page 24). MD-E9000H - Listening to the Radio - Auto tuning: Radio D F To receive an FM stereo transmission: Press the TUNER (BAND) button to display "ST". q "j" will appear when an FM broadcast is in stereo. FM stereo mode indicator FM stereo receiving indicator V q If the FM reception is weak, press the TUNER (BAND) button to extinguish "ST". The reception changes to monaural, and the sound becomes clearer. After use: Press the ON/STAND-BY button to enter the power stand-by mode. S I N E E-20 *07-E20-21-MD9000H(SEEG) 20 01. 4. 19, 3:08 PM Listening to a Memorised Station s Memorising a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) s To recall a memorised station When in the tuner mode, press the PRESET (X or W) button to seX lect the desired station. 1 2 - Listening to a Memorised Station - Perform the steps 1 - 3 in "Listening to the Radio" on page 20. Press the MEMORY/ENTER button to enter the preset tuning saving mode. Within 5 seconds, press the PRESET (X or W) button to select the preset channel number. s To clear all memorised stations 1 Press the CLEAR/DELETE button on the remote control for 3 seconds or more. 2 Within 10 seconds, press the MEMORY/ENTER button. 3 Radio Store the stations in memory, in order, starting with preset channel 1. 4 Within 5 seconds, press the MEMORY/ENTER button to store that station in memory. If the "MEMORY" and preset number indicators go out before the station is memorised, repeat the operation from step 2. 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorised will be erased. Note: The backup function protects the memorised stations for a few hours should there be a power failure or the AC power lead disconnection. E-21 *07-E20-21-MD9000H(SEEG) 21 01. 4. 19, 3:08 PM Using the Radio Data System (RDS) RDS is a broadcasting service which a growing number of FM stations provide. These FM stations send additional signals along with their regular programme signals. They send their station names, and information about the type of programme such as sports or music, etc. When tuned to an RDS station, "RDS" and the station name will be displayed. "TP" (Traffic Programme) will appear on the display when the received broadcast carries traffic information, and "TA" (Traffic Announcement) will appear whilst a traffic information is on air (see page 28). "EON" will appear whilst the EON (Enhanced Other Networks information) data is broadcast. You can control the RDS by using the remote control only. MD-E9000H s Information provided by RDS Each time the DISPLAY/CHARACTER button is pressed, the display will switch as follows: Station name (PS) Programme type (PTY) Frequency When you are tuning in to a station other than an RDS station or to an RDS station which sends weak signal, the display will change in the following order: - Using the Radio Data System (RDS) - RDS Radio D F S V I N E E-22 *07-E22-28-MD9000H(SEEG) 22 01. 4. 19, 3:08 PM Using the Radio Data System (RDS) (continued) Descriptions of the PTY (Programme Type) codes, TP (Traffic Programme) and TA (Traffic Announcement) You can search for and receive the following PTY, TP and TA signals. NEWS AFFAIRS Short accounts of facts, events and publicly expressed views, reportage and actuality. [. . . ] q Has condensation formed inside the unit? F s MiniDisc Symptom q A recording cannot be made. Possible cause q Is the MiniDisc protected against acci- S dental erasure? q Did you try to make recording on a play- V back-only MiniDisc?q Can you see the "DISC FULL" or "TOC FULL" message in the display? q Even though a disc has been q Is the unit located near excessive vibra- I loaded, "CD/MD NO DISC" or "Can't READ" is displayed. q Playback sounds are skipped. tion? q Is the disc very dirty?q Has condensation formed inside the N unit? [. . . ]