User manual SHARP MD-R2H OPERATION MANUAL

[. . . ] YO <P=001> MINIDISC DECK MODEL MD-R2H OPERATION MANUAL Thank you for purchasing this SHARP product. CONTENTS Page SPECIAL NOTES . . 38 ACCESSORIES Remote control × 1 "AA" size battery (UM/SUM-3, R6, HP-7 or similar) × 2 (for remote control) Analogue connecting cable × 2 Note: Parts and equipment mentioned in this operation manual other than those shown above are not included. MD-R2E SM <P=001> SPECIAL NOTES NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. [. . . ] This feature is also convenient for identifying specific points with one selection so that you can locate those points easily whenever you like. (Page 22) 1 2 3 MOVE The order of the recorded tracks can be changed. This feature is different from programme play. A new track order can be recorded directly on the disc. When the power is turned off, the revised order will not be changed. (Page 24) 1 2 3 4 A 1 2 B 3 C 4 D 1 A 2 B 3 C 4 D A B C D C A B D COMBINE Two adjacent tracks (for example, the third and fourth tracks) can be combined. If there is a prolonged silent section in the middle of a selection that is recorded, a single piece of music may be recorded as two tracks. If this happens, these two tracks can be combined into a single track. (Page 23) Programme move function This function allows the track numbers to be automatically rearranged in the order specified for programmed playback. The track numbers will be adjusted as needed, automatically. (The tracks that are not included in the programmed selections will be put at the end of the new track numbers. ) (Page 24) 1 2 3 4 1 2 3 4 A 1 2 B 3 C D 1 A 2 B 3 C 4 D A B C D C A D B ERASE Tracks you want to erase can be erased one at a time or all at once. Once a track has been erased, it cannot be recovered. Double-check the track number before erasing it. (Page 25) TRACK/DISC NAME You can assign titles to recorded tracks and to discs. The characters must be capital and lowercase letters, or symbols. Track and disc names can use up to 100 characters per name. (Page 26) 1 2 3 4 5 A 1 2 B C 3 4 D E DISC 4 TOTAL 1234567 8 9 10 11 12 13 14 15 16 17 18 A B D E 20 MD-R2E (Continued) s Using the editing function We will show you some examples of how to use the editing functions. You can create a disc of your favourite selections by recording tracks from a variety of input sources such as CDs, tapes, and radio broadcasts. STEP 1 Recording tracks to be edited on an MD Digital recording from a CD Recording a broadcast Analogue recording from tape A B C D D Talk E Live performance STEP 2 Putting the space between tracks in order A B C D D Talk E Live performance The tracks are combined using the combine function. A B C D The tracks are divided using the divide function. Talk E F G CM H STEP 3 Cutting unnecessary sections Cut using the erase function. Cut using the erase function. G H STEP4 Rearranging tracks in your preferred order A B C D E F The tracks are rearranged using the programme move function. D E A C B H The track is moved using the move function. [. . . ] q Press the ON/STAND-BY button to enter the stand-by mode, and wait for a while. q Replace the disc with another disc. PROTECTED TEMP OVER TOC ERR* TOC FULL* TOC W ERROR U TOC ERR* U TOC W ERR q Replace it with another recordable disc. q Ask the store where you purchased this unit, about repairs. q Erase all the data, and try recording. [. . . ]