User manual SHARP MX-M182/D/M202D/M232D DRIVERPCFAX

[. . . ] 37 · TRAY SETTINGS FOR THE LARGE CAPACITY TRAYS (MX-LCX5) . 40 · TRAY SETTINGS FOR THE LARGE CAPACITY TRAY (MX-LCX6) . 43 · TRAY SETTINGS FOR THE LARGE CAPACITY TRAY (MX-LCX3N) . 48 · IMPORTANT POINTS WHEN USING THE BYPASS TRAY. [. . . ] If the original is placed on the document glass, follow these steps to start scanning and transmission: (1) Press the [START] key ( ). (2) When scanning is finished, replace the original with the next original. (4) Repeat (2) and (3) until all originals have been scanned. (5) Touch the [Read-End] key. Transmission begins When transmission ends, image settings and convenient special mode settings are cleared. Press the [STOP] key ( ) to cancel the operation. System Settings (Administrator): Default Display Settings The settings can be kept in effect a fixed period of time after scanning is completed. 23 ORIGINAL SIZES TRANSMITTABLE ORIGINAL SIZES The following original sizes can be transmitted Minimum original size Using the automatic document feeder 5-1/8" (height) x 5-1/2" (width) (131 mm (height) x 140 mm (width)) ­ Maximum original size 11" (height) x 31-1/2"* (width) (297 mm (height) x 800 mm* (width)) 11" (height) x 17" (width) (297 mm (height) x 432 mm (width)) Using the document glass * A long original can be transmitted. (The original will be scanned in Mono2. ) THE SIZE OF THE PLACED ORIGINAL When a standard size original is placed, the original size is automatically detected and displayed in "Scan" in the base screen. When the automatic original detection function is operating and the original is a non-standard size, the closest standard size may be displayed or the original size may not appear. In this event, manually set the correct original size. Specifying the original scan size (by paper size) (page 71) Specifying the original scan size (by numerical values) (page 72) Standard Sizes Standard sizes are sizes that the machine can automatically detect. The standard sizes are set in "Original Size Detector Setting" in the system settings (administrator). The factory default setting is "Inch-1". You can also delete a destination from the list (cancel selection of the destination). 5 10 15 To Cc Touch the [Address Review] key. BBB BBB DDD DDD FFF FFF HHH HHH JJJ JJJ 1 2 Condition Settings Address Review Address Entry AAA AAA CCC CCC EEE EEE GGG GGG III III Frequent Use ABCD 1 Global Address Search EFGHI JKLMN OPQRST UVWXYZ Sort Address Auto Reception Fax Memory:100% Address Review OK Check the destinations and then touch the [OK] key. 1 2 001 AAA AAA 003 KKK KKK 005 MMM MMM 007 OOO OOO 009 QQQ QQQ 011 SSS SSS To 002 BBB BBB 004 LLL LLL 006 NNN NNN 008 PPP PPP 010 RRR RRR 012 TTT TTT Cc 2 To check Cc or Bcc destinations, touch the corresponding tab. Touch the one touch-key of the destination that you wish to cancel. A message appears to confirm the cancelation. Touch the [Yes] key. Deselect the address?AAA AAA No Yes 27 USING A SEARCH NUMBER TO RETRIEVE A DESTINATION A destination stored in the address book can be retrieved using the of the modes or in the address book screen. This can be done in the base screen of any Scan Address Book Address Entry Send Settings Internet Fax Original Exposure Resolution File Format Color Mode Special Modes Fax Scan: Auto 200X200dpi PDF Mono2 Auto Data Entry 8½x11 Send: USB Mem. Scan Auto Touch the key. Text 1 Address Review File Quick File PDF Enter the 3-digit search number of the address with the numeric keys. When the 3-digit search number is entered, the stored address is retrieved and specified as a destination. 2 · The search number is programmed when the destination is stored in the address book. · If you do not know the search number, print the one-touch address list using "Sending Address List" in the system settings. · When entering search numbers such as "001" and "011", "0" can be omitted. For example to enter "001", enter "1" and touch the key or the [Next Address] key. If an incorrect search number is entered. . . [. . . ] Output tray*1 Select the output tray for received faxes. Number of Prints Set the number of copies of received faxes that are printed. Staple Position*1 Use this setting to specify stapling positions for received faxes. This setting is only effective when [Staple] is enabled in "Fax Data Receive/Forward". [. . . ]