User manual SHARP MX-M3100N

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. Trademark acknowledgments The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and accessories. Microsoft, Windows, Windows 98, Windows Me, Windows NT 4. 0, Windows 2000, Windows XP, Windows Server 2003 and Internet Explorer are registered trademarks or trademarks of Microsoft Corporation in the U. S. A. [. . . ] (The next step is not needed. ) [When using the document glass:] Replace the original with the next original and press the [START] key. Repeat this operation until all originals have been scanned and then touch the [READ-END] key. NOTES When the pamphlet copy function is set, the twosided copying mode will be automatically selected. If this function is used in combination with the pamphlet copy function (pamphlet stapling) and the number of origial pages exceeds the number of pages that can be stapled, a message asking you to select "CANCEL", "CONTINUE", or "DIVIDE" will appear. To cancel the job, select "CANCEL". To make pamphlet copies without stapling, select "CONTINUE". To divide the pages into sets that can be stapled, select "DIVIDE". If you performed steps 4 to 6 to insert cover paper, divided stapling is not possible. You can either continue pamphlet copying without stapling, or cancel the job. To cancel the pamphlet copy function, touch the [CANCEL] key on the pamphlet copy setting screen (step 2). 5 7 Touch the [OK] key. CANCEL OK G RIGHT BINDING COVER SETTING 8 Touch the [OK] key. OK CANCEL OK Return to the main screen of copy mode. LEFT BINDING RIGHT BINDING COVER SETTING 5-7 SPECIAL MODES Job build Use job build mode when you need to copy more original pages than can be loaded at once in the document feeder (the maximum number of pages that can be loaded is 150). This function allows the original pages to be scanned in sets. If "XY ZOOM" was initially set for the ratio, it will not be possible to change the ratio setting. When job build mode is used in combination with any of the following functions, the [CHANGE] key will not appear in the screen of step 5. Pamphlet copy, tandem copy, covers/inserts, transparency inserts, multi-shot, book copy, tab copy, staple sort, saddle stitch 5-9 SPECIAL MODES Tandem copy Two machines connected to the same network can be used to run a large copy job in parallel. By dividing the job in half, approximately half the time is required to complete the job. To use this function, two machines must be connected to your network as network printers. Even if more machines are connected to the network, this function can only be used to have one other machine share a job. Server machine and client machine In the following explanations, the machine on which the copy job is initially set up and tandem copy selected is called the server machine. The other machine that is asked to share the job is called the client machine. To use the tandem copy function, the tandem settings must be configured in the administrator settings. (See page 14 of the "Administrator settings guide") When configuring the tandem settings in the server machine, the IP address of the client machine must be entered. For the port number, it is best to use the initial setting (50001). [. . . ] 1-15 [SCAN TO HDD] key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 [SEARCH] key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 Searching for a file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13 to 7-14 8-6 INDEX Troubleshooting -Copier operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]