User manual SHARP MX-M450U

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. CONTENTS CAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Some applications can start automatically from Network Scanner Tool and some cannot. When the auto-run function of an application is enabled, Network Scanner Tool will start the application with the ". exe" command using the file name as a parameter. Normally an application is started twice, once for the image file and once for the XML file. For example, when Network Scanner Tool is set to start the application "APP. EXE", the following commands are applied when the two files "IMG. TIF" and "IMG. XML" are received. APP. EXE IMG. TIF APP. EXE IMG. XML 4 Note 85 TRANSMITTING METADATA Follow the steps below to select a metadata set, enter each item, and perform metadata transmission. 1 Touch the [DATA ENTRY] key. 5 Touch the key of the value that you wish to enter. CANCEL 3 6 OK ADDRES ADDRES DATA ENTRY SEND S Value2 Value4 Value6 DIRECT ENTRY 1/9 Note If no metadata sets have been stored, the [DATA ENTRY] key cannot be selected. Store a metadata set in the Web pages and then perform the transmission procedure. 2 Touch the key of the metadata that you wish to use. CANCEL OK If the entry values of the metadata item were stored in selection format, the selections will appear as keys. If a value is editable, the [DIRECT ENTRY] key can be touched to manually enter a value. If a metadata item requires the entry of text, a text entry screen will appear. Enter the required information. Note METADATA 2 METADATA 4 METADATA 6 METADATA 8 1/2 To change the number of items that appear at once, touch the display item number select key. Each time the key is touched, the number of items displayed switches between 3 and 6. 3 ATA 2 ATA 4 ATA 6 ATA 8 Touch the [OK] key. 6 Touch the [OK] key. CANCEL OK CANCEL 3 Value2 Value4 Value6 6 OK 1/2 DIRECT ENTRY 1/9 4 The keys of the items stored in the metadata set will appear. Touch the key of the item that you wish to enter. METADATA SE 7 Enter all items. READY TO SEND. This chapter explains system settings (general) that can be configured by general users. The system settings include the following settings: TOTAL COUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . This displays the number of pages output by the machine. (p. 92) DISPLAY CONTRAST . . . . . . . . . . . . . . . . This is used to adjust the contrast of the touch panel. (p. 92) LIST PRINT*1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . This is used to print a setting list or a font list. (p. 92) CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . This is used to set the date and time of the machine's built-in clock. (p. 92) TRAY SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . This is used to configure the paper type and paper size settings for each tray, and select whether or not automatic switch over to another tray with the same size and type of paper will take place if the paper runs out during continuous printing. [. . . ] The system settings can be configured in the Web pages as well as on the operation panel. To access the system settings using the Web pages, a password is also required. Factory default administrator password Factory default setting: 00000 Store a new administrator password as soon as the machine is installed. Once the administrator password has been changed, the new password is required to restore the factory default password. Take care to remember the new password. Factory default passwords (Web pages) There are two factory default accounts: "Administrator" and "User". [. . . ]