User manual SHARP PG-B10S

[. . . ] Introduction Basic Operation Projection Functions Using the Menu Connections Screen Setup Appendix OPERATION MANUAL PG-B10S MODEL LCD PROJECTOR IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 9. Model No. : PG-B10S Serial No. : This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] for weaker blue. Press | for more contrast. for stronger blue. Description of Color Temperature Settings Selectable settings 5500K 6500K 7500K 8500K 9300K 10500K Description For lower color temperature for warmer, reddish incandescent-like images. For higher color temperature for cooler, bluish, fluorescent-like images. Note · "Color", "Tint" and "Sharp" are not displayed when selecting INPUT 1 and setting the "Signal Type" to "RGB" or setting the "Signal Type" to "Auto" and the input signal is recognized as an RGB signal. · "Red" and "Blue" cannot be adjusted when "sRGB" is set to "ON". · "Sharp" can be adjusted when 480I, 480P, 540P, 580I, 580P, 720P, 1035I or 1080I signals are detected while "Signal Type" for INPUT 1 is set to "Component" or set to "Auto" and the input signal is recognized as a component signal. · To reset all adjustment items, select "Reset" and press . Note · Values for "CLR Temp" are only approximations. · "CLR Temp" cannot be set when "sRGB" is set to "ON". -36 Gamma (Gamma Correction) sRGB (sRGB Setting) Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. When you are displaying images with frequent dark scenes, such as a film or concert, or when you are displaying images in a bright room, this feature makes the dark scenes easier to see and gives the impression of greater depth in the image. When you want to display the image in a natural tint based on an original image from the computer, select "sRGB" and set it to " " (ON). Select "sRGB" on the "Picture" menu and set it to " " (ON). Setting the menu screen Page 34 Select "Gamma" on the "Picture" menu and the desired gamma mode. Setting the menu screen Page 34 Example: "Picture" screen menu for INPUT 1 (RGB) mode Example: "Picture" screen menu for INPUT 1 (RGB) mode Using the Menu Note · When "sRGB" is set to " " (ON); · Gamma is not available. · "Red", "Blue" or "CLR Temp" on the "Picture" menu cannot be adjusted. · For additional information about the sRGB function, visit "http://www. srgb. com/". Description of Gamma Modes Selectable settings Description Standard For standard image Presentation Brightens darker portions of image for more enhanced presentations. Cinema Gives greater depth to darker portions of image for a more exciting theater experience. Game For natural color gradation for playing a game, etc. Info · When "sRGB" is set to " " (ON), the projected image may become dark, but this does not indicate a malfunction. Note · Gamma is not available for INPUT 1 when "sRGB" on the "Picture" menu is set to "ON". -37 Picture Adjustment Signal Type (Signal Type Setting) The signal type setting is preset to "Auto"; however, in rare cases a clear picture may not be displayed. In that case, select "RGB" or "Component" in accordance with the input signal. Memory (Storing and Selecting the Adjustment Settings) Use this function to store the adjustment settings on the "Picture" menu. No matter which input mode or signal type is selected, you can select and apply the settings you have stored in a memory location. Select "Signal Type" on the "Picture" menu and set it to "Auto", "RGB" or "Component" for INPUT 1. Setting the menu screen Page 34 Example: "Picture" screen menu for INPUT 1 (RGB) mode Select "Memory" on the "Picture" menu and the memory location where you want to store the settings. Then adjust the setting items on the "Picture" menu. Setting the menu screen Page 34 Example: "Picture" screen menu for INPUT 1 (RGB) mode Description of Signal Type Settings Selectable settings Description Auto Input signals are automatically recognized as RGB or Component. Component Set when Component signals are received. Description of Memory Positions Selectable settings Description 1 2 3 4 5 Settings of all items on the "Picture" menu can be stored in memory location. The stored settings can be selected in any input mode. Memory Memory Memory Memory Memory Memory OFF Besides "Memory 1" to "Memory 5", other settings on the "Picture" menu can be stored for each input mode. The settings stored in "Memory OFF" cannot be applied when another input mode is selected. If you want to apply the stored settings on the "Picture" menu, select "Memory" on the "Picture" menu and the memory location where you have stored the settings. Note · You can change the stored settings after selecting the memory location for those settings. -38 Computer Image Adjustment Using the "Fine Sync" menu, you can adjust the computer image, match the computer display mode, and check the input signal. Adjusting the Computer Image When "Auto Sync" is set to OFF or when vertical stripes or flickering occur in portions of the screen even if "Auto Sync" is set to ON, adjust "Clock", "Phase", "H-Pos" or "V-Pos" to obtain the best computer image. Special Modes Mode Settings) (Special Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in "Special Modes" on the "Fine Sync" menu may need to be selected to match the computer display mode. Select the item on the "Fine Sync" menu and adjust the computer image. Adjusting the menu screen Page 32 Select "Special Modes" on the "Fine Sync" menu and the appropriate resolution. Setting the menu screen Page 34 Example: "Fine Sync" menu screen for INPUT 1 mode Example: "Fine Sync" menu screen for INPUT 1 mode Using the Menu Description of Adjustment Items Selectable items Use \ and | to Clock adjust vertical noise. Phase adjust horizontal noise (similar to tracking on your VCR). H-Pos center the on-screen image by moving it to the left or right. V-Pos center the on-screen image by moving it up or down. Note · If your computer displays patterns which repeat every other line (horizontal stripes), flickering may occur which makes the image hard to see. [. . . ] 23 Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Remote control sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Replacing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]