User manual SHARP PG-C455W

[. . . ] Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. [. . . ] · When turning off the power in the case of connecting an amplifier or other audio equipment, first turn off the power of the amplifier and then turn off the power of the projector. · By using external audio components, the volume can be amplified for better sound. · For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 57. -28 Turning the Projector On/Off Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Supplied accessory Power cord Turning the Projector on Before performing the steps in this section, connect any equipment that you use with the projector. (See pages 23-28. ) Info · English is the factory preset language. If you want to change the on-screen display to another language, change the language according to the procedure on page 60. Remove the lens cap and press projector or on the on the remote control. · The power indicator illuminates green. · After the lamp indicator illuminates, the projector is ready to start operation. · When System Lock is set, the keycode input screen appears. Enter the right keycode to start projection. See page 53 for details. ON button STANDBY button Power indicator Lamp indicator Note · The lamp indicator illuminates or blinks, indicating the status of the lamp. Blinking green: The lamp is warming up or shutting down. · Straight lines or the edges of images may appear jagged while adjusting the image. · The Manual Keystone Correction can be adjusted up to an angle of approximately ±35 degrees and the screen can also be set up to an angle of approximately ±35 degrees (when the resize mode is set to "NORMAL" (see page 36)). The screen can also be installed by inclining to that angle. · The Keystone Correction cannot be adjusted in the lateral direction. · You can use the same settings used in NORMAL mode 4:3 for 16:9. -31 3 Press . · The on-screen display of the Keystone Correction mode will disappear. · You can also use on the projector. Image Projection Adjusting the Focus When adjusting the focus using the buttons on the projector on the remote control ZOOM/FOCUS button Adjustment buttons ('/"/\/|) 1 Press . 2 Adjust by pressing \ or |. Adjust by pressing the FOCUS buttons. Adjusting the Projected Image Size When adjusting zoom using the buttons on the projector 1 Press . FOCUS buttons ZOOM buttons on the remote control Adjust by pressing the ZOOM buttons. 2 Adjust by pressing ' or ". Note · After you have pressed the FOCUS buttons or ZOOM buttons on the remote control, or after you have pressed the ZOOM/FOCUS button on the projector, you can display the test pattern by pressing the ENTER button. The test pattern is useful for making more accurate adjustments. -32 Switching the INPUT Mode Select the appropriate input mode for the connected equipment. Press , , or on the remote control to select the input mode. · When pressing ' or " on the projector, input mode switches in order of : / / / INPUT buttons "On-screen Display of INPUT Mode (Example) INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 1/2 mode Using RGB Note · When no signal is received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is received, "NOT REG. " will be displayed. · The INPUT mode is not displayed when "OSD Display" of the "Options1" menu is set to " " (OFF). (See page 50. ) About the INPUT mode INPUT 1/ INPUT 2 (RGB/ Component) INPUT 3 (Video) INPUT 4 (S-Video) Used for projecting images from equipment that sends RGB signals or component signals connected to the RGB input terminal. [. . . ] 24, 40 Rear adjustment feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Remote control sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]