User manual SHARP PG-C45X

[. . . ] Introduction Connections and Setup Basic Operation Easy to Use Functions Appendix OPERATION MANUAL PG-C45X MODEL LCD PROJECTOR IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 14. Model No. : PG-C45X Serial No. : This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] · In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the threetwo pull down enhancement will be enabled automatically, when the film source has been entered. · In PAL50Hz or SECAM, the two-two pull down enhancement will be enabled only in the Film Mode, when the film source has been entered. · Basic Operation -47 Adjusting Computer Images Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen. Selected Item Clock Phase H-Pos V-Pos Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centers the on-screen image by moving it to the left or right. Centers the on-screen image by moving it up or down. Description When Auto Sync is OFF When "Auto Sync" is "OFF", interference such as flickering or vertical stripes may occur if displaying tilings or vertical stripes. Should this occur, adjust "Clock", "Phase", "H-Pos" and "V-Pos" for obtaining an optimum image. Select "Clock", "Phase", "H-Pos" or "VPos" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · Computer image adjustments can be made . See page 50 for easily by pressing details. Saving Adjustment Settings This projector allows you to store up to seven adjustment settings for use with various computers. Select "Save Setting" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. -48 Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Select "Select Setting" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · If a memory position has not been set, a resolution and frequency setting will not be displayed. · When selecting a stored adjustment setting with "Select Setting", you can set the projector in the stored adjustments. Special Mode Settings Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in "Special Modes" on the "Fine Sync" menu screen may need to be selected to match the computer display mode. Basic Operation Set the resolution by selecting "Special Modes" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see. ) · When a DVD player or Digital Video is connected, select 480P as the input signal. · See "Checking the Input Signal" below for information on the currently selected input signal. Checking the Input Signal This function allows you to check the current input signal information. Select "Signal Info" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · The projector will display the number of scanned lines available from audio-visual equipment such as a DVD player or Digital Video. -49 Adjusting Computer Images Auto Sync Adjustment Used to automatically adjust a computer image. Select "Auto Sync" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note When setting to " Normal" or " High Speed": · Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a computer. Manual adjustments should be performed: · When the optimum image cannot be achieved with Auto Sync adjustment. · Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector. · When setting "Auto Sync" to "OFF" or is pressed Auto "High Speed", and if Sync will be executed in "High Speed" mode. [. . . ] 49 Selecting the on-screen display language . . . . . . . . . . 36 Signal Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Signal Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 SMART STRETCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]