User manual SHARP PG-D120U

[. . . ] Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. [. . . ] This may damage your computer. 24 When connecting to the LAN terminal using a LAN cable LINK LED (green) Illuminates when linked. TX/RX LED (yellow) Illuminates when transmitting/receiving data. * To ensure safety, do not connect the LAN terminal with any cables that may cause excessive voltage such as a telephone line. Hub or Computer To LAN terminal Connections LAN cable (Category 5 type, commercially available) Note · When connecting to a hub, use a straight-through Category 5 (CAT. 5) type cable (commercially available). · When connecting to a computer, use a cross-over Category 5 (CAT. 5) type cable (commercially available). Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet. AC socket To AC outlet Power cord (supplied) 25 Turning the Projector On/Off Info Turning the Projector On Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 25. ) Open the lens shutter fully and press STANDBY/ON on the projector or ON on the remote control. · The power indicator illuminates green. · After the lamp indicator illuminates, the projector is ready to start operation. · When "Auto Restart" is set to "On": If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 50. ) · English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 49. Power indicator Lamp indicator STANDBY/ON button Note · About the Lamp Indicator The lamp indicator illuminates to indicate the status of the lamp. Blinking in green: The lamp is warming up. (Move the slide bar in the - direction. ) 3 Press KEYSTONE. · The on-screen display of the Keystone Correction mode will disappear. Info · While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged. 29 Image Projection (Continued) Switching the Input Mode Select the appropriate Input mode for the connected equipment. Press INPUT / to display the INPUT list. Use INPUT / to select the Input mode, and use O/Q to select the audio input terminal. INPUT buttons AV MUTE button VOL +/­ (Volume) buttons O/Q buttons Adjusting the Volume Press VOL +/­ on the remote control or ­O/Q+ on the projector to adjust the volume. Note · Pressing VOL­/­O will lower the volume. · Pressing VOL+/Q+ will raise the volume. · When the projector is connected to external equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector's volume to the lowest level when turning the projector on/off or when changing the input signal. · When you do not want to output the sound from the projector's speaker while the projector is connected to external equipment, set "Speaker" in the "PRJ-ADJ1" menu to "Off". (See page 50. ) On-screen display Displaying the Black Screen and Turning Off the Sound Temporarily Press AV MUTE on the remote control or close the lens shutter to temporarily display a black screen and turn off the sound. On-screen display Note · Pressing AV MUTE again will turn the projected image back on. · When you close the lens shutter, the projector will be set to AV Mute mode and then the projector will be turned off automatically after about 30 minutes. 30 Resize Mode This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image. Press RESIZE. · See page 47 for setting on menu screen. RESIZE button NORMAL FULL NATIVE 800 × 600 1068 × 800 1024 × 768 1152 × 864 1400 × 1050 1000 × 800 1280 × 720 1280 × 722 1280 × 720 1280 × 768 1280 × 800 -- Output screen image 1280 800 1280 × 1024 -- 1360 × 768 1366 × 768 -- 1280 × 720 -- 1280 × 720 16:9 COMPUTER SVGA (800 × 600) 4:3 aspect ratio XGA (1024 × 768) SXGA (1152 × 864) SXGA+ (1400 × 1050) SXGA (1280 × 1024) 1280 × 720 Other aspect ratios 1360 × 768 1366 × 768 1280 × 768 1280 × 800 Input signal Computer Resolution XGA and below Resolution higher than XGA *3 4:3 aspect ratio Image type NORMAL FULL NATIVE 16:9 *1 Basic Operation SXGA (1280 × 1024) 5:4 aspect ratio 1280 × 720 16:9 aspect ratio 1360 × 768 1366 × 768 16:9 aspect ratio *1 1280 × 768 15:9 aspect ratio 1280 × 800 16:10 aspect ratio : Cutout area on which images cannot be projected : Area where the signals are off screen *1 The Image Shift function can be used for these images. [. . . ] · The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones. · Cables are incorrectly connected to the projector or the connected equipment works improperly. · If this happens frequently, replace the lamp. [. . . ]