User manual SHARP PG-D210U

[. . . ] La lingua delle istruzioni d'uso incluse nel CD-ROM varia in relazione al modello. De meegeleverde CD-ROM bevat handleidingen. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt. De taal van de gebruiksaanwijzing in de bijgeleverde CD-ROM hangt af van het model. [. . . ] The following precautions are recommended to minimize the potential for experiencing visual problems or any adverse symptoms. Take regular breaks, at least 5 to 15 minutes after every 30 to 60 minutes of stereoscopic 3D viewing. * Based on the guidelines issued by the 3D Consortium revised December 10, 2008. Maintain an appropriate distance from the screen. Viewing from too close a distance can strain your eyes. If you experience eye strain, immediately discontinue viewing. If you experience any of the following symptoms during viewing: ­ nausea ­ queasiness/dizziness ­ headache ­ blurry vision or double vision that lasts longer than few seconds Do not engage in any potentially hazardous activity for example, driving a vehicle until your symptoms have completely gone away. If symptoms persist, discontinue use and do not resume stereoscopic 3D viewing without discussing your symptoms with a physician. As you get more comfortable viewing stereoscopic 3D: · Adjust the parallax on the 3D-video playback equipment. (You may not be able to adjust the parallax on some models of equipment. ) · Adjust the projected image to the most comfortable viewing size by zooming. (Projecting images on the smallest or largest screen size possible may eliminate the stereoscopic effect and strain your eyes. ) · Use the DLP® LinkTM Invert function to properly set the video for your left and right eyes. (For details on using DLP® LinkTM Invert , see the section on its operation in this operation manual. ) 2 WARNING The following people should limit stereoscopic 3D viewing: ­ Children under 6 years of age (to protect the eye growth process) ­ People with a history of photosensitivity ­ People with heart disease ­ People in poor health ­ People who are sleep deprived ­ People who are physically tired ­ People under the influence of drugs or alcohol Epilepsy A small percentage of the population may experience epileptic seizures when viewing certain types of images that contain flashing patterns of light. IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY The following people should consult a physician before viewing stereoscopic 3D images. ­ Anyone with a history of epilepsy, or who has a family member with a history of epilepsy ­ Children under 6 years of age ­ Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY Discontinue use if you experience any of the following symptoms while viewing stereoscopic 3D images. ­ Involuntary movements, eye or muscle twitching ­ Muscle cramps ­ Nausea, dizziness, or queasiness ­ Convulsions ­ Disorientation, confusion, or loss of awareness of your surroundings 3 Information on the 3D Projection Function · To display 3D images, this projector requires: WHAT YOU WILL NEED 1 Source devices that support the field sequential format ­ For details on the supported signals, see the Compatibility Chart in this operation manual. · Block any ambient light. Ghosting (a double image) occurs without the image appearing in 3D. Check that you are using 3D LCD shutter glasses that support the DLP® LinkTM system. · Be sure to use 3D LCD shutter glasses that support the DLP® LinkTM system. Check that the shutters on the 3D LCD shutter glasses are working properly. · Turn the 3D LCD shutter glasses off and then on again. · Check the batteries of the 3D LCD shutter glasses. · Check that the 3D LCD shutter glasses are set to 3D viewing mode. ­ Some 3D LCD shutter glasses are equipped with a special viewing mode (such as dual view mode ) in addition to the normal 3D viewing mode. See the operation manual of your 3D LCD shutter glasses. · Turn the DLP® LinkTM function On . · Use DLP® LinkTM Invert to change the setting. Check whether a signal that is not supported is being input. [. . . ] ­ Any obstructions may cause the glasses not to function properly causing the lenses to flicker or turn off. Do not place your hand or other objects in front of the 3D control signal sensor on the glasses. Check whether there is a source of high intensity lighting nearby. · Block the light or turn it off. [. . . ]