User manual SHARP PG-D2870W

[. . . ] Introduction DATA PROJECTOR MODEL Easy Start PG-D3550W PG-D3050W PG-D2870W OPERATION MANUAL Setup Connections Basic Operation Useful Features PG-D3550W/PG-D3050W Appendix IMPORTANT · For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. · Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 11. Model No. : Serial No. : ii SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. [. . . ] · After the lamp indicator illuminates, the projector is ready to start operation. · When "Auto Restart" is set to "On": If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 50. ) · English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 49. Power indicator Lamp indicator STANDBY/ON button Note · About the Lamp Indicator The lamp indicator illuminates to indicate the status of the lamp. Blinking in green: The lamp is warming up. Red: The lamp is shut down abnormally or the lamp should be replaced. · When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation. · If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection. · When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 51 for details. STANDBY button ON button On-screen display (confirmation message) Turning the Power Off (Putting the Projector into Standby Mode) Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the confirmation message is displayed, to put the projector into Standby mode. · The projector cannot be turned on while cooling. Info · Direct Power Off function: You can unplug the power cord from the AC outlet even if the cooling fan is still running. 26 Image Projection Setup Guide screen (e. g. PG-D3550W/PG-D3050W) About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM* Press ENTER to exit the Setup Guide screen. Note · The Setup Guide screen automatically highlights the items in the following order: 1 FOCUS 4 ENTER 2 HEIGHT ADJUST 3 ZOOM* ENTER button However, you can adjust the focus, height (angle) or zoom* regardless of the highlighted item. · If you do not want to display the Setup Guide for the next time, set "Menu" - "SCR - ADJ" "Setup Guide" to "Off". (See page 49. ) * The PG-D2870W model is not equipped with the ZOOM function. Basic Operation Adjusting the Projected Image 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Rotate the focus ring to adjust the focus while watching the projected image. · Using the knob on the focus ring will make the adjustments easier. PG-D2870W Focus ring 27 Image Projection (Continued) 2 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. Make small adjustments. HEIGHT ADJUST lever 2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted. · The angle of projection is adjustable up to 9 degrees from the surface on which the projector is placed. Rear adjustment foot 3 Use the rear adjustment foot to make the projector level. · The projector is adjustable ±2 degrees from the standard position. Info · Do not apply too much pressure on the projector when the front adjustment foot comes out. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. · Hold the projector firmly while lifting or carrying. · Do not hold by the lens area. Note · When adjusting the height of the projector, trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the distortion. [. . . ] · The lamp will eventually need to be changed. While the remaining lamp life draws to a close, replace the lamp. 21­25 61 61 15 15 This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes. 66 For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the "Troubleshooting" section on pages 65 and 66. [. . . ]