User manual SHARP PG-D4010X

[. . . ] DATA PROJECTOR MODEL PG-D4010X SETUP MANUAL Connecting Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RS-232C Specifications and Commands . . . . . . . . . . . 4 Setting up the Projector Network Environment . . . Connecting the Projector to a Computer . . . . . . . . . . . 10 2. [. . . ] · You can input the characters below: a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ', . , @, ` (You can input "@" only one time. ) · For details about error items, refer to the projector's operation manual. Example of the display when an error occurs -19 Setting up the Projector Using RS-232C or Telnet Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector. When Connecting Using RS-232C 7 Input "setup" and press the "Enter" key. · SETUP MENU will be displayed. 1 2 Launch general purpose terminal emulator. Input settings for the RS-232C port of the terminal emulator as follows. Baud Rate Data Length Parity Bit Stop Bit Flow Control : 9600 bps* : 8 bit : None : 1 bit : None SETUP MENU -----------------------------SETUP MENU---------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> Note · User name and password are not set in the factory default settings. · If the user name or password is entered incorrectly three times, SETUP MENU will be quit. * This is the factory default setting. If the value of Baud Rate for the projector has been changed, set Baud Rate here according to the changed value on the projector. 3 4 5 Input "PJS11234" and press the "Enter" key. Input "PJS25678" and press the "Enter" key within 10 seconds. Input the user name and press the "Enter" key. · If a user name has not yet been set, just press the "Enter" key. 6 "Password:" is displayed. Input the password and press the "Enter" key. · If a password has not yet been set, just press the "Enter" key. -20 Setting up the Projector Using RS-232C or Telnet SETUP MENU When Connecting Using Telnet 1 2 Click "Start" from the Windows® desktop and select "Run". Enter "telnet 192. 168. 150. 2" in the text box that opens up. (If the IP address of the projector is 192. 168. 150. 2. ) Click the "OK" button. -----------------------------SETUP MENU---------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> Note · If the IP address has been changed, be sure to enter the new IP address in step 2. · User name and password are not set in the factory default settings. · If the user name or password is entered incorrectly three times in steps 4 or 5, SETUP MENU will be quit. 3 4 "User Name:" is displayed. Input the user name and press the "Enter" key. · If a user name has not yet been set, just press the "Enter" key. 5 "Password:" is displayed. Input the password and press the "Enter" key. · If a password has not yet been set, just press the "Enter" key. 6 Input "setup" and press the "Enter" key. · SETUP MENU will be displayed. -21 Setting up the Projector Using RS-232C or Telnet SETUP MENU SETUP MENU (Main Menu) ADVANCED SETUP MENU ADVANCED SETUP MENU ********************** ADVANCED SETUP MENU *************************** [1]Auto Logout Time [2]Data Port [5]Network Ping Test [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr [0]Search Port -----------------------------SETUP MENU---------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> [!]Restore Default Setting [Q]Return to Main Menu [1] IP Address IP address settings. (Page 25) [2] Subnet Mask Subnet mask settings. (Page 25) [3] Default Gateway Default gateway settings. (Page 25) [4] User Name (Factory default setting: Not Required) Setting of user name for security protection. (Page 25) [5] Password (Factory default setting: Not Required) Setting of password for security protection. (Page 26) [6] RS-232C Baud Rate (Factory default setting: 9600 bps) Baud rate settings for the RS-232C terminals. (Page 26) [7] Projector Name It is possible to assign a projector name. (Page 26) [8] DHCP Client DHCP Client settings. (Page 26) [A] Advanced Setup Enters ADVANCED SETUP MENU. (Page 27) [D] Disconnect All Disconnect all connections. [. . . ] (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". Note · When "DHCP Client" is set to "OFF" on the projector: IP address: 192. 168. 150. 2 Subnet mask: 255. 255. 255. 0 Gateway address: 0. 0. 0. 0 (Not Used) · For network settings for the projector, refer to page 13. -32 Troubleshooting \ Take the following steps for checking the network settings for the computer. · In the case of Windows® 2000: click "start" "Programs" "Accessories" "Command Prompt" in order. · In the case of Windows® XP, Windows Vista®: click "start" "All Programs" "Accessories" "Command Prompt" in order. After launching the command prompt, enter the command "ipconfig", and press the "Enter" key. Note · Communication may not be established even after carrying out the network settings for the computer. [. . . ]