User manual SHARP PG-D50X3D

[. . . ] Introduction Quick Start Setup Connections Basic Operation Useful Features Appendix PG-D50X3D PG-D45X3D DATA PROJECTOR MODEL OPERATION MANUAL IMPORTANT · For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. · Before recycling the packag ing, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 11. Model No. : Serial No. : ii SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse and of the same rating as above, which is also indicated on the pin face marked or of the plug, must be used. [. . . ] Blinking in green: The lamp is warming up. Red: The lamp is shut down abnormally or the lamp should be replaced. · When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation. · If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection. · When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 46 for details. Lamp indicator STANDBY button ON button Turning the Power Off (Putting the Projector into Standby Mode) Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the confirmation message is displayed, to put the projector into Standby mode. · The projector cannot be turned on while cooling. On-screen display (confirmation message) Info · Direct Power Off function: You can unplug the power cord from the AC outlet even if the cooling fan is still running. 26 Image Projection Adjusting the Projected Image 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Rotate the focus ring to adjust the focus while watching the projected image. Zoom ring Focus ring 2 Adjusting the Height The height of the projector can be adjusted using the adjustment feet. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. HEIGHT ADJUST lever 2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted. · The angle of projection is adjustable up to 9 degrees from the surface on which the projector is placed. Basic Operation Make small adjustments. Note · When adjusting the height of the projector, trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the distortion. (See pages 28 and 43. ) Info · Do not apply too much pressure on the projector when the front adjustment feet come out. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment feet and the projector. · Hold the projector firmly while lifting or carrying. · Do not hold by the lens area. 3 Adjusting the Picture Size You can adjust the picture size using the zoom ring on the projector. Rotate the zoom ring to enlarge or shrink the picture size. 27 Image Projection (Continued) Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. Note · The Keystone Correction can be adjusted up to an angle of approximately ±40 degrees and the screen can also be set up to an angle of approximately ±40 degrees (when the Resize mode is set to "NORMAL" (see page 30)). Adjustment buttons (P/R/O/Q) RETURN button KEYSTONE button On-screen display (Keystone Correction mode) KEYSTONE ADJUST 0 END 1 Press KEYSTONE to enter the Keystone Correction mode. · You can also display the on-screen display of the Keystone Correction mode with KEYSTONE on the projector. Shrinks upper side. (Move the slide bar in the + direction. ) 2 Press P/Q or O/R to adjust the Keystone Correction. · You can also adjust the Keystone Correction using the adjustment buttons on the projector. Note · To return to the default setting, press RETURN while the on-screen display of the Keystone Correction mode is on the screen. Shrinks lower side. (Move the slide bar in the - direction. ) 3 · The on-screen display of the Keystone Correction mode will disappear. · You can also use KEYSTONE on the projector. Press KEYSTONE. Info · While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged. 28 Switching the Input Mode Select the appropriate Input mode for the connected equipment. Press COMPUTER, DVI, S-VIDEO or VIDEO on the remote control to select the Input mode. · When you press INPUT on the projector or DVI on the remote control, the INPUT list appears. [. . . ] Make sure the batteries are inserted correctly or insert new ones. 8, 9 52, 53, 54 53, 56, 57 21­25 51 56 56 The lamp needs much time to turn on. The remote control cannot be used. 15 15 This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes. 60 For SHARP Assistance If you encounter any problems during setup or operation of this projector, fi rst refer to the "Troubleshooting" section on pages 59 and 60. [. . . ]