User manual SHARP PG-F212X-L

[. . . ] Introduction Quick Start Setup Connections Basic Operation Useful Features Appendix PG-F212X-L DATA PROJECTOR MODEL OPERATION MANUAL IMPORTANT · For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. · Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 10. Model No. : Serial No. : ii SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. [. . . ] ENTER END PAGE 2 Picture Picture Mode CLR Temp BrilliantColor TM C. M. S. Progressive DNR Lamp Setting Reset 0 1 On 3D Progressive Off Bright SCR - ADJ PRJ - ADJ Standard Help CLR Temp -1 1 Page 41 BrilliantColorTM 0 2 Page 41 C. M. S. Setting [On/Off] Page 41 C. M. S. Page 41 Progressive *2 Page 42 SEL. /ADJ. ENTER END DNR 2D Progressive 3D Progressive Film Mode Off Level 1 Level 2 Bright Eco + Quiet Page 42 Lamp Setting "C. M. S. " C. - Value Reset R Y G C B M Reset SEL. /ADJ. Return 0 0 0 0 0 0 ENTER END Page 42 Reset C. M. S. -Hue R Y G C B M Reset -30 -30 -30 -30 -30 -30 +30 +30 +30 +30 Page 41 C. M. S. -Saturation Page 41 C. M. S. -Value Useful Features +30 +30 Page 41 Reset *1 Items when inputting RGB signal through COMPUTER or DVI. *2 Items when inputting component signal through COMPUTER or DVI, or when selecting S-VIDEO or VIDEO. 35 Menu Items (Continued) "Screen adjustment (SCR-ADJ)" menu Picture Resize Image Shift Keystone OSD Display Background Setup Guide PRJ Mode Language SCR - ADJ 0 0 On Logo On Front English PRJ - ADJ Border Help Main menu SCR - ADJ Resize Sub menu Page 43 Page 43 Image Shift -96 +96 Page 43 Keystone -80 +80 Normal Full Dot By Dot Area Zoom V-Stretch Border Stretch Normal Area Zoom V-Stretch Border Stretch Page 43 OSD Display [On/Off] COMPUTER/ DTV VIDEO/ S-VIDEO Page 43 Background Page 44 SEL. /ADJ. ENTER END Setup Guide [On/Off] Logo Blue None Page 44 PRJ Mode Page 44 Language Front Ceiling + Front Rear Ceiling + Rear English Deutsch Español Nederlands Français Italiano Svenska Português polski Magyar Türkçe Page 44 "Projector adjustment (PRJ-ADJ)" menu Picture SCR - ADJ PRJ - ADJ Help Main menu PRJ - ADJ Auto Sync [On/Off] Sub menu Auto Sync Auto Power Off Auto Restart STANDBY Mode System Sound Speaker Audio Input RS-232C Fan Mode System Lock Lamp Timer(Life) SEL. /ADJ. 0h ENTER On On On Standard On On Audio 1 9600bps Normal Disable 0 min 100% END Page 45 Page 45 Auto Power Off [On/Off] Page 45 Auto Restart [On/Off] Page 45 STANDBY Mode Page 45 System Sound [On/Off] Standard Eco Page 45 Speaker [On/Off] Page 45 Audio Input Page 46 RS-232C Audio 1 Audio 2 9600bps 115200bps Normal High Page 46 Fan Mode Page 46 System Lock [Enable/Disable] Page 46 Lamp Timer(Life) Page 47 36 "Help" menu Picture SCR - ADJ PRJ - ADJ Help The items you can set with the "Help" menu "Help" menu n Page 48 · Vertical stripes or flickering image appear Auto Sync Clock Phase · Data image is not centered Auto Sync H-Pos V-Pos · Color is faded or poor COMPUTER/COMPONENT or DVI input Signal type: Auto/RGB/Component S-VIDEO or VIDEO input Video System: Auto/PAL/SECAM/ NTSC3. 58/NTSC4. 43/ PAL-M/PAL-N/PAL-60 DVI (Digital) input Dynamic range: Auto/Standard/Enhanced * The selectable items vary depending on the input signal and the selected input mode. There is no picture or audio Vertical stripes or flickering image appear Data image is not centered Color is faded or poor Picture is dark The image is distorted Reset all adjustments to default settings SEL. SEL ENTER END 37 Useful Features Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button ENTER button Adjustment buttons (P/R/O/Q) RETURN button · Press RETURN to return to the previous screen when the menu is displayed. MENU/HELP button Menu Selections (Adjustments) Example: Adjusting "Bright". · This operation can also be performed by using the buttons on the projector. 1 2 Press MENU/HELP. · The "Picture" menu screen for the selected input mode is displayed. Example: "Picture" screen menu for COMPUTER (RGB) input Menu item Press Q or O and select "Picture" to adjust. Picture SCR - ADJ PRJ - ADJ Standard 0 0 0 0 0 1 On Off Bright Help Picture Mode Contrast Bright Red Blue CLR Temp BrilliantColor TM C. M. S. DNR Lamp Setting Reset SEL. /ADJ. ENTER END 38 3 Press P or R and select "Bright" to adjust. · The selected item is highlighted. Picture SCR - ADJ PRJ - ADJ Standard 0 0 0 0 0 1 On Off Bright Help Picture Mode Contrast Bright Red Blue CLR Temp BrilliantColor TM C. M. S. DNR Lamp Setting Reset SEL. /ADJ. Single ADJ END Items to be adjusted Picture Resize Image Shift Keystone SCR - ADJ 0 0 PRJ - ADJ Border Help To adjust the projected image while watching it Press ENTER. · The selected item (e. g. "Bright") is displayed by itself at the bottom of the screen. · When pressing P or R, the following item ("Red" after "Bright") will be displayed. Press ENTER. The item displayed by itself Picture Bright SEL. /ADJ. Menu END Note · Press ENTER again to return to the previous screen. 4 Press O or Q to adjust the item selected. · The adjustment is stored. Picture SCR - ADJ PRJ - ADJ Standard 0 15 0 0 0 1 On Off Bright Help 5 Press MENU/HELP. · The menu screen will disappear. Picture Mode Contrast Bright Red Blue CLR Temp BrilliantColor TM C. M. S. DNR Lamp Setting Reset SEL. /ADJ. Useful Features Single ADJ END Note · Menu buttons do not function while the projector is operating the "Auto Sync", "Break Timer", "FREEZE", or "AV MUTE" functions. 39 Picture Adjustment ("Picture" Menu) Menu operation n Page 38 Q PAGE1 Picture SCR - ADJ PRJ - ADJ Standard 0 0 0 0 0 0 0 Help Q PAGE2 Picture Picture Mode SCR - ADJ PRJ - ADJ Standard 0 1 On 3D Progressive Off Bright Help 1 2 Picture Mode Contrast Bright Color Tint Sharp Red Blue 3 2 4 5 6 7 CLR Temp BrilliantColor TM C. M. S. Progressive DNR Lamp Setting Reset SEL. /ADJ. ENTER END SEL. /ADJ. ENTER END 1 Selecting the Picture Mode Selectable items Standard The default settings of each item when selecting Picture Mode Description CLR Temp For standard image 0 0 ­1 0 ­ BrilliantColorTM 1 2 0 1 ­ Lamp Setting Bright Bright Eco + Quiet Bright Bright Presentation Brightens portions of image for more enhanced presentations. Movie Game *sRGB Gives natural tint to the projected image. For high fidelity reproduction of images from a computer. · "sRGB" is displayed only when RGB signal is input. · You can set or adjust each item in the "Picture" menu to your preference. Any changes you make are retained in memory. Note · You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33. ) · *sRGB is an international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are displayed in a natural tint based on an original image, when "sRGB" is selected. [. . . ] 37, 48 Image shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 INPUT modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Intake vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 49 Kensington Security Standard connector . . . . . . . . . . . . . . . [. . . ]