User manual SHARP PG-LW3000/LX3000/LW3500/LX3500 SETUP MANUAL

[. . . ] DATA PROJECTOR MODEL PG-LW3500 PG-LW3000 PG-LX3500 PG-LX3000 SETUP MANUAL Connecting Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RS-232C Specifications and Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operating the Projector Using the PJLinkTM Protocol. . . . . . . . . . . . . . . . . . . 10 Setting up the Projector Network Environment. [. . . ] Setting up a Network Connection for the Projector Settings for such items as the projector's IP address and subnet mask are compatible with the existing network. Set each item on the projector as follows. (See page 62 of the projector's operation manual for setting. ) DHCP Client: Off IP Address: 192. 168. 150. 002 Subnet Mask: 255. 255. 255. 000 1 Start Internet Explorer (version 6. 0 or later) on the computer, and enter “http://192. 168. 150. 2/” in “Address”, and then press the “Enter” key. If a user name and a password have not yet been set, just click the “OK” button. • If a user name and a password have been set, input the user name and the password, and click the “OK” button. • If the user name or password is entered incorrectly three times, an error message will be displayed. • When you are using Internet Explorer 7 or later, other setup screen may be displayed. In this case, make the proper adjustments for the setup screen. 2 3 When the screen as shown on the right appears, click “TCP/IP”. -15 Setting up the Projector Network Environment 4 The TCP/IP setting screen Items appears, ready for network settings for the projector. Setting example / Remarks New You can set the password to protect Password the TCP/IP setting. DHCP Client IP Address Select “ON” or “OFF” to determine whether to use DHCP Client. You can set this item when “DHCP Client” is set to “OFF”. Factory default setting: 192. 168. 150. 2 Enter an IP address appropriate for the network. You can set this item when “DHCP Client” is set to “OFF”. Factory default setting: 255. 255. 255. 0 Set the subnet mask to the same as that of the computer and equipment on the network. You can set this item when “DHCP Client” is set to “OFF”. Factory default setting: 0. 0. 0. 0 * When not in use, set to “0. 0. 0. 0”. Factory default setting: 0. 0. 0. 0 * When not in use, set to “0. 0. 0. 0”. Subnet Mask Default Gateway DNS Server Note • Confirm the existing network's segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If “192. 168. 150. 2” is not used in the network having an IP address of “192. 168. 150. XXX”, you don't have to change the projector IP address. • For details about each setting, consult your network administrator. 5 Click the “Apply” button. Confirm that the values are set properly, and then click the “Confirm” button. • Close the browser. • This completes the network settings. • After setting items, wait for about 15 seconds and then re-access. • Change the IP address of the setting computer back to its original address, which you have noted down in Step 6-1 on page 14, and then connect the computer and the projector to the network. -16 Controlling the Projector via LAN After connecting the projector to your network, enter the projector IP address in “Address” on Internet Explorer (version 6. 0 or later) using a computer on the network to start a setup screen that will enable control of the projector via the network. Controlling the Projector Using Internet Explorer Complete connections to external equipment before starting the operation. [. . . ] • IP Address Check that the IP address for the projector is not duplicated on the network. • Subnet Mask When the gateway setting for the projector is “0. 0. 0. 0” (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: • The subnet masks for the projector and the computer should be the same. • The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is “192. 168. 150. 2” and the subnet mask is “255. 255. 255. 0” for the projector, the IP address for the computer should be “192. 168. 150. X” (X=3-254) and the subnet mask should be “255. 255. 255. 0”. [. . . ]