User manual SHARP PG-M15S

[. . . ] Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. Quest apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC. Este equipamento obedece às exigências das directivas 89/336/CEE e 73/ 23/CEE, na sua versão corrigida pela directiva 93/68/CEE. Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/ 23/CEE, modificadas por medio de la 93/68/CEE. [. . . ] This will return the projector to the normal operating condition. Do not set up the projector in places exposed to direct sunlight or bright light. n Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room. The projector may be safely tilted to a maximum angle of ±12 degrees. n Placement should be within ±12 degrees of horizontal. Caution regarding transportation of the projector. n When transporting the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Before moving the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables connected to it. Other connected equipment Do not subject the projector to hard impact and/or vibration. n Take care with the lens so as not to hit or damage the surface of the lens. n When connecting a computer or other audiovisual equipment to the projector, make the connections AFTER turning off the projector and the equipment to be connected. n Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections. Rest your eyes occasionally. n Continuously watching the screen for long hours will cause eye strain. Be sure to occasionally rest your eyes. Using the projector in other countries n The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, be sure to use an appropriate power cord for the country you are in. Avoid locations with extremes of temperature. 4 English Introduction Product Features This product is an XGA single chip 0. 7 DLPTM projector. The outstanding features of it are listed as follows: u True XGA, 1024 x 768 addressable pixels u 3. 97 lbs (1. 8 kgs) compact design u Single chip DLPTM technology u PureProgressiveTM processing technology for artifactfree film materials. u HDTV compatible (480i, 480P, 580i, 580P, 720P/1080i/ 60Hz) u NTSC/NTSC4. 43/PAL/PAL-M/PAL-N/SECAM and HDTV compatible u High-tech DVI connection for digital and analog video connectivity u Full function remote with mouse control and laser pointer u Multimedia audio integration u User friendly multilingual on-screen display menu u Advanced electronic keystone correction and high quality full screen re-scaling image u User friendly control panel u Luxurious carrying case included u SXGA compression and VGA, SVGA re-sizing u 150 Watts P-VIP lamp u Mac compatible 5 English Introduction Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Lower down the projector, then release the button to lock the elevator foot into position. Use to fine-tune tilt-adjustment. 1 Elevator Button 2 Elevator Foot 3 13 English Installation Adjusting the Projector Zoom / Focus You may adjust zoom ring to zoom in / out. Rotate the zoom ring counter-clockwise to zoom in and clockwise to zoom out. To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 3. 74 feet to 39. 37 feet (1. 14m to 12m) Zoom Ring Focus Ring Adjusting Projection Image Size Max. Screen Max. (WxH) Min. (WxH) Size Distance 28. 1" 23. 4" 22. 48" x 16. 86" 18. 72" x 14. 04" 3. 74' 98. 4" 82. 0" 78. 72" x 59. 04" 65. 60" x 49. 20" 13. 12' 123. 0" 102. 5" 98. 40" x 73. 80" 82. 00" x 61. 50" 16. 40' 196. 9" 164. 0" 157. 52" x 118. 14" 131. 20" x 98. 40" 26. 25' 246. 1" 205. 1" 196. 88" x 147. 66" 164. 08" x 123. 06" 32. 81' 295. 3" 246. 1" 236. 24" x 177. 18" 196. 88" x 147. 66" 39. 37' vThis graph is for users reference only. 14 English User Controls Panel Control & Remote Control There are two ways for you to control the functions: Remote Control and Panel Control. Panel Control Remote Control Use the Remote Control Power / Standby 4 Refer to the Power On/Off the Projector section on page 11~12. Source 4 Press Source to choose RGB, DVI-Digital, DVI-Analog, S-Video, Composite, Component and HDTV sources. Re-Sync 4 Automatically synchronizes the projector to the input source, when you press this button while the remote control cover is opened. functions like the right mouse button. 4 If the remote control cover is closed, the Mouse/Re-Sync button 15 English User Controls Multi-Directional Selector 4 When you close the cover of remote control, this key can be used as a mouse to control direction. v The above function is only enabled with the connection between computer and projector by USB cable. 4 When the cover of remote control is opened, this key can be used for the operation for OSD display. vPage Up / Page Down : Under remote mouse connected status only. Page Up (Computer mode only) 4 Use this button to page up. Laser Page Down (Computer mode only) 4 Use this button to page down. 4 Aim the remote at the viewing screen, press and hold this button to activate the laser pointer. Menu 4 Press Menu to open the on-screen display (OSD) menus and key to select menu items. To exit OSD, press the press Menu button again. The projector will save any change you made automatically. Freeze 4 Press the Freeze button to still the screen image. Mute 4 Use to mute sound. Volume + / - 4 Increases/decreases speaker volume. Keystone + / degrees) 4 Adjust image distortion caused by tilting the projector. [. . . ] 4 Make sure you have removed the lens cap and the projector is switched on. Problem : Partial, scrolling or incorrectly displayed image. 4 Press the Re-Sync button on the Remote Control or the Panel 4 Control. If you use a PC: If the resolution of your computer is higher than 1024 x 768. Follow the steps outlined below to reset the resolution. In the Windows Program Manager, click the Windows Setup icon in the Main group. [. . . ]