User manual SHARP PG-M15X

[. . . ] No. PARTS LIST PARTS REPLACEMENT Part No. 5 Description Code Ref. No. ERSATZTEILLISTE AUSTAUSCH VON TEILEN Part No. 5 Description Code Parts marked with "å" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Les pieces marquées "å" sont importantes pour maintenir la sécurité de l'appareil. [. . . ] Ne pas faire fonctionner plus de 2 heures avec le coffret retiré. Précautions pour les radiations UV et la lampe moyenne pression 1. To u j o u r s d é b r a n c h e r l a f i c h e AC l o r s d u remplacement de la lampe. Laisser l'unité refroidir pendant une heure avant de procéder à l'entretien. Ne remplacer qu'avec une lampe du même type. Type 9HJ7083119001 ou BQC-PGM15X//1 caractéristique 85V/130W. La lampe émet de petites quantités de radiation UVéviter tout contact direct avec les yeux. La lampe moyenne pression implique un risque d'explosion. Toujours suivre les instructions d'installation décrites ci-dessous et manipuler la lampe avec soin. PG-M15X PG-M15S AN-M15T Lamp Replacement Note: Since the lamp reaches a very high temperature during units operation replacement of the lamp should be done at least one hour after the power has been turned off. (to allow the lamp to cool off. ) Installing the new lamp, make sure not to touch the lamp (bulb) replace the lamp by holding its reflector 2. [Use original replacement only. ] 1 Lamp 2 Reflector DANGER !­­ Never turn the power on without the lamp to avoid electric-shock or damage of the devices since the stabilizer generates high voltages at its start. Since small amounts of UV-Radiation are emitted from an opening between the duct cover and the lamp housing, it is recommended to place the LENS CAP on the opening during servicing to avoid eye and skin exposure (Fig. Handle the remote control carefully. 9 PG-M15X PG-M15S AN-M15T Connection Pin Assignments DVI INPUT 1 Port: 29-pin Pin No. 1 2 3 4 5 6 7 8 9 16 8 1 10 C2 C1 11 12 13 14 · *1 Return for 5 V, Hsync. 15 2 · * These pins are not used on this equipment. 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5 C4 C3 24 17 9 C5 DVI input Name T. M. D. S. Data 4 *2 DDC Clock DDC Data Vertical Sync T. M. D. S. Data 3 *2 5 V Power Ground*1 Hot Plug Detect T. M. D. S. Clock Analog input Red Analog input Green Analog input Blue Horizontal Sync Ground RGB input Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5 Name Not connected Not connected Not connected Not connected Not connected DDC Clock DDC Data Vertical Sync Not connected Not connected Not connected Not connected Not connected 5 V Power Ground Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Analog input Red Analog input Green Analog input Blue Horizontal sync Ground COMPONENT input Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5 Name Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Ground Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Not connected Analog input Pr Analog input Y Analog input Pb Not connected Ground 10 PG-M15X PG-M15S AN-M15T OUTPUT (INPUT 1) Signal Port: 15-pin Mini D-sub female connector RGB output Analog 1 Video output (red) 2 Video output (green/sync on green) 3 Video output (blue) 4 Not connected 5 Not connected 6 Earth (red) 7 Earth (green/sync on green) 8 Earth (blue) 9 Not connected 10 GND 11 GND 12 Not connected 13 Horizontal sync signal 14 Vertical sync signal 15 Not connected COMPONENT output Analog 1 PR (CR) 2Y 3 PB (CB) 4 Not connected 5 Not connected 6 Earth (PR) 7 Earth (Y) 8 Earth (PB) 9 Not connected 10 Not connected 11 Not connected 12 Not connected 13 Not connected 14 Not connected 15 Not connected 11 6 1 15 10 5 RS-232C Terminal: 7-pin Mini DIN female connector 6 7 5 Pin No. 1 2 3 4 5 6 7 Signal VCC (USB) RD SD USB ( ) GND USB ( ) NC Name USB Power Receive Data Send Data USB Data ( ) Signal Ground USB Data ( ) (Reserved) 4 3 2 1 RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable 1 5 Pin No. 1 2 3 4 5 6 7 8 9 Signal CD RD SD ER SG DR RS CS CI Name Receive Data Send Data Signal Ground Data Set Ready Request to Send Clear to Send 6 9 USB connector: 4-pin USB connector of the USB mouse control cable Pin No. [. . . ] Calling the process adjustment mode 1) Turn on the power. Press the ON/OFF button on the projector or the POWER button on the remote controller. 2) Make sure the message "Turn Power OFF?" on the screen. With this message still onscreen, press the buttons in this order: "'", "'", """ and """ on the remote controller, or "+", "+", "-" and "-" on the projector. [. . . ]