User manual SHARP PGA20X OPERATION MANUAL

[. . . ] Introduction Connections and Setup Basic Operation Easy to Use Functions Appendix OPERATION MANUAL PG-A20X MODEL LCD PROJECTOR IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 14. Model No. : PG-A20X Serial No. : This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] · Straight lines or the edges of images may appear jagged while adjusting the image. Compresses lower side. 3 Press · You can also use . on the projector. Note · You can use the same settings used in NORMAL mode 4:3 for 16:9. -29 Menu Items This list shows the items that can be set in the projector. I INPUT 1 Mode Main menu Picture Page 36 Contrast Bright Color Tint Sharp Red Blue Reset CLR Temp 5500 K 6500 K 7500 K 8500 K 9300 K 10500 K Standard Presentation Cinema Game -30 -30 -30 -30 -30 -30 -30 +30 +30 +30 +30 +30 +30 +30 Eco Mode [Eco/Standard] Auto Power Off [ON/OFF] Menu Position Center Upper Right Lower Right Upper Left Lower Left OSD Display [ON/OFF] Background Sharp Blue None Sub menu Main menu Options Page 44 Lamp Timer (Life) Keystone Auto Manual Sub menu Gamma Menu Color [Opaque/Translucent] Password Old Password New Password Reconfirm Old Code New Code Reconfirm sRGB [ON/OFF] Signal Type Auto RGB Component Memory 1 Memory 5 Memory OFF -30 -15 -30 -30 Language Page 28 Anti-Theft Memory Fine Sync Page 38 Clock Phase H-Pos V-Pos Reset +30 +15 +30 +30 English Deutsch Español Nederlands Français Italiano Svenska Português Special Modes Auto Sync Signal Info PRJ Mode Page 50 Front Ceiling+Front Rear Ceiling+Rear Note · In the "Picture" menu of INPUT 1, "Color", "Tint" and "Sharp" are only displayed when "Signal Type" is set to "Component" or set to "Auto" and the input signal is recognized as a component signal. · In the "Picture" menu of INPUT 1, "sRGB" is only displayed when "Signal Type" is set to "RGB" or set to "Auto" and the input signal is recognized as an RGB signal. -30 I INPUT 2 / 3 Mode Main menu Picture Page 36 Contrast Bright Color Tint Sharp Red Blue Reset CLR Temp 5500 K 6500 K 7500 K 8500 K 9300 K 10500 K Standard Presentation Cinema Game Memory 1 Memory 5 Memory OFF PRJ Mode Page 50 Front Ceiling+Front Rear Ceiling+Rear -30 -30 -30 -30 -30 -30 -30 +30 +30 +30 +30 +30 +30 +30 Sub menu Main menu Language Page 28 English Deutsch Español Nederlands Français Italiano Svenska Português Gamma Memory Basic Operation Options Page 44 Lamp Timer (Life) Keystone Auto Manual OSD Display [ON/OFF] Video System Auto PAL NTSC3. 58 SECAM NTSC4. 43 PAL-M PAL-N PAL-60 Sharp Blue None Background Eco Mode [Eco/Standard] Auto Power Off [ON/OFF] Menu Position Center Upper Right Lower Right Upper Left Lower Left Menu Color [Opaque/Translucent] Password Old Password New Password Reconfirm Old Code New Code Reconfirm Anti-Theft -31 Using the Menu Screen The menu screens allow you to adjust the image and various projector settings. You can operate the menus from the remote control using the following procedure. Example: "Picture" menu screen for INPUT 1 (RGB) mode Menu Selections (Adjustments) 1 Press . · The "Picture" menu screen for the selected input mode is displayed. ENTER button UNDO button MENU button ', ", \, | buttons Note · The on-screen display shown on the right is displayed when the INPUT 1 (RGB) mode is selected. 2 Press \ or | to display the other menu screens. · The menu icon for the selected menu screen is highlighted. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Menu icons Note · The "Fine Sync" menu is not available for INPUT 2 or 3. · For details on the menus, see the tree charts on pages 30 and 31. -32 3 Press ' or " to select the item you want to adjust. · The selected item is highlighted. Note · To display a single adjustment item, press after selecting the item. Only the selected adjustment item will be displayed. Then if you press ' or ", the following item ("Red" after "Bright") will be displayed. to return to the previous 4 Press \ or | to adjust the item selected. · The adjustment is stored. Basic Operation 5 Press . · The menu screen will disappear. -33 Using the Menu Screen Menu Selections (Settings) 1 Press . · The "Picture" menu screen for the selected input mode is displayed. ENTER button UNDO button MENU button ', ", \, | buttons Note · The on-screen display shown on the right is displayed when INPUT 1 (RGB) mode is selected. Menu icons 2 Press \ or | to display the other menu screens. · The menu icon for the selected menu screen is highlighted. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Note · The "Fine Sync" menu is not available for INPUT 2 or 3. · For details on the menus, see the tree charts on pages 30 and 31. -34 3 Press ' or " to select the item you want to set, and then press | to display the sub menu. · The selected item is highlighted. Note · Press or \ to return to the previous screen. · For some items, press \ or | to select the icon using " ". Sub menu 4 Press ' or " to select the setting of the item displayed in the sub menu. Basic Operation 5 6 Press . · The item selected is set. Press . · The menu screen will disappear. -35 Picture Adjustment You can adjust the projector's picture to your preferences using the "Picture" menu. For operation of the menu screen, see pages 32 to 35. Example: "Picture" screen menu for INPUT 1 (RGB) mode Adjusting the Image Select the item on the "Picture" menu and adjust the image. Description of Adjustment Items Selectable items Contrast Bright Color Tint Sharp Red Blue Press \ for less contrast. for weaker blue. CLR Temp (Adjusting the Color Temperature) Select "CLR Temp" on the "Picture" menu and the desired color temperature setting. Description of Color Temperature Settings Selectable settings 5500K 6500K 7500K 8500K 9300K 10500K Description For lower color temperature for warmer, reddish incandescent-like images. Press | for more contrast. for stronger blue. For higher color temperature for cooler, bluish, fluorescent-like images. Note · "Color", "Tint" and "Sharp" are not displayed when selecting INPUT 1 and setting the "Signal Type" to "RGB" or setting the "Signal Type" to "Auto" and the input signal is recognized as an RGB signal. · "Sharp" can be adjusted when 480I, 480P, 540P, 580I, 580P, 720P, 1035I or 1080I signals are detected while "Signal Type" for INPUT 1 is set to "Component" or set to "Auto" and the input signal is recognized as a component signal. · To reset all adjustment items, select "Reset" and press . Note · Values for "CLR Temp" are only approximations. -36 Gamma (Gamma Correction) Signal Type (Signal Type Setting) The signal type setting is preset to "Auto"; however, in rare cases a clear picture may not be displayed. In that case, select "RGB" or "Component" in accordance with the input signal. Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. [. . . ] 26 PRJ mode (Reversing/Inverting Projected Images) . . . . 50 Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Remote control sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]