User manual SHARP PGM10XE OPERATION MANUAL

[. . . ] ENGLISH OPERATION MANUAL MODEL PG-M10X PG-M10S FRANÇAIS DEUTSCH ITALIANO ESPAÑOL DIGITAL MULTIMEDIA PROJECTOR This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG. [. . . ] 1280 × 1024) are compressed into 1024 × 768. In such a case, projected letters and lines might appear unevenly. PG-M10S The resolution of the unit is 800 × 600. 1024 × 768) are compressed into 800 × 600. In such a case, projected letters and lines might appear unevenly. * Due to native pixel resolution of the panels (800 × 600), this unit will not display Mac 832 × 624 resolution images full screen. 27 Manual Adjustment of Personal Computer Images Adjusting Clock Frequency and Phase Adjusting the position of the image If the image is offset up, down, left or right, adjust the vertical and horizontal position. 1 2 3 4 5 6 Select RGB as the input (page 20). Press the MENU button to display the main menu and then press the cursor / keys to select the "IMAGE". / keys to select the 1 2 3 Perform steps 1 - 6 for "Adjusting the Clock Frequency and Phase" on this page. / keys and select Press the cursor / keys and adjust the image width in relation to the screen. Adjustment is performed in dot units. Adjust to the position where vertical flicker disappears. Press the cursor /, / keys and adjust the horizontal and vertical position. Press the cursor "PHASE". / keys and select Press the cursor / keys and adjust to minimize image noise, flicker, color variations, etc. Reconnecting a separate personal computer or other device to the COMPUTER input terminal Either press the AUTO SYNC button on the main unit or open the FLIP COVER of the remote control and press the AUTO SYNC button there. Menu Operation If no images appear during setting Use the following procedure when no images appear during setting because the clock frequency or phase is grossly inaccurate. 1 Turn off the power of all devices connected. The input signal will stop and either a blue or black background (This depends on the "BACKGROUND" setting on page 32) will be projected. 3 Readjust the "CLOCK" and "PHASE" To close the menu Press the R-CLICK/UNDO button. 28 Resetting Resetting the factory defaults All items can be reset to the standard settings with the exception of the followings. · Lamp usage timer · "KEYSTONE" adjustment values (including the "KEYSTONE" setting value on page 32). Resetting the Lamp Usage Timer When the lamp is replaced (page 37), it is necessary to set the lamp hours of usage from the menu. 1 2 3 1 2 3 Press the remote control MENU button to display the normal menu and then press the cursor / keys to select "INFORMATION". When the "INFORMATION" menu appears, press the cursor / keys select "RESET", then press the ENTER button. If the ENTER button is not used during reset, press the R-CLICK/UNDO button. Press the remote control MENU button, use the cursor / keys to display the "INFORMATION" menu and set the lamp hours of usage. Display the "INFORMATION" menu, use the cursor / keys to select "LAMP USAGE HOURS RESET" and then press the ENTER button. If the ENTER button is not used during reset, press the R-CLICK/UNDO button. When the lamp usage timer has exceeded 1100 hours and the unit will not turn on The power will not turn on when the lamp hours of usage has exceeded 1100 hours. The STATUS indicator will be on continually (page 36). In such case, replace the lamp housing, then use the following procedure to reset. 1 2 Connect the power cord (page 18). Standby status will be activated. Press the INPUT SELECT and AUTO SYNC buttons of the main unit at the same time for 5 sec. or more. The lamp usage timer will be reset. [. . . ] 9 Remote control sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Remote control signal transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 12 RIGHT-CLICK button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 21, 26 S Signal type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]