User manual SHARP PN-V600A

[. . . ] PN-V600A LCD MONITOR OPERATION MANUAL IMPORTANT: To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product. Model No. : Serial No. : U. S. A. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: • The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth or coloured green or green-and-yellow. • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. [. . . ] AUDIO SELECT Selects the terminal used to input audio signals in each input mode. INPUT SIGNAL (PC D-SUB/PC RGB) If a computer connected to the PC D-sub/PC RGB input terminal outputs any of the following resolutions, make a selection from the following options. A 480 LINES. . . . . . . . . . .  UTO, 640x480 or 848x480 768 LINES. . . . . . . . . . .  UTO, 1024x768, 1280x768, 1360x768 or A 1366x768 1050 LINES. . . . . . . . . 1400x1050 or 1680x1050 ZOOM2 SPECIAL SETTING (See page 29. ) SCAN MODE (AV input) Sets the scan mode used for AV mode input. . . . . . . . . . . . . . .  nder-scan display when the input signal . Otherwise, over-scan display E *  ven when MODE1 is selected, under-scan display is used when the input signal is 1080i/p and the screen size is Dot by Dot. POWER MANAGEMENT POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode. COLOR SYSTEM (AV S-VIDEO/AV VIDEO) Select the color system of the AV equipment which is connected to AV S-video and AV video input terminal. (AUTO / PAL / PAL-60 / SECAM / NTSC3. 58 / NTSC4. 43) When AUTO is selected, the color system is automatically set according to the input signal. AUDIO OUTPUT(RCA) Sets the volume of sound output from the audio output terminals. When set to VARIABLE2, audio is not output from the external speaker terminals. VARIABLE. . . . . . . . . . .  ou can adjust the volume using VOLUME. Y FIXED. . . . . . . . . . . . . . . . . .  isables volume adjustment and fixes the D sounds. When the PN-ZB02 (optional) is attached: VARIABLE1. . . . . . . . .  ou can adjust the volume using VOLUME. Y VARIABLE2. . . . . . . . .  ou can adjust the volume using VOLUME, Y but audio is not output from the external speaker terminals. FIXED. . . . . . . . . . . . . . . . . .  isables volume adjustment and fixes the D sounds. AUDIO LEVEL(STEREO MINI) Selects the maximum audio input level of the audio input terminal. SELF ADJUST On a PC D-SUB/PC RGB screen, specify whether to perform screen adjustment automatically or not. When ON is selected, the screen is automatically adjusted when its resolution is 800 x 600 or higher and the timing of input signals changes. “ADJUSTING” appears on the screen during the adjustment. For images with black edges, etc. , depending on the signal, adjustment may not be possible. (Perform manual adjustment of the screen. ) AUTO INPUT CHANGE Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode, AUTO INPUT CHANGE automatically changes the selected mode to another mode where a video signal is present. [. . . ] SCL SDA DDC/CEC GND +5V Hot-plug detection Hot-plug detection TMDS data 0TMDS data 0+ TMDS data 0/5 shield N. C. TMDS clock shield TMDS clock+ TMDS clock- nPC D-sub input (Mini D-sub 15 pin) terminal pins nRS-232C input (D-sub 9 pin) terminal pins No. 1 2 3 4 5 6 7 8 Function Red video signal input Green video signal input Blue video signal input N. C. GND GND for red video signal GND for blue video signal No. [. . . ]