User manual SHARP QT-MP3W

[. . . ] Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. PORTABLE CD STEREO SYSTEM MODEL QT-MP3W / OPERATION MANUAL Wiring diagram of this model is subject to change for improvement without prior notice. Wiring diagram of this model is subject to change for improvement without prior notice. Wiring diagram of this model is subject to change for improvement without prior notice. Wiring diagram of this model is subject to change for improvement without prior notice. Wiring diagram of this model is subject to change for improvement without prior notice. Wiring diagram of this model is subject to change for improvement without prior notice. Wiring diagram of this model is subject to change for improvement without prior notice. Wiring diagram of this model is subject to change for improvement without prior notice. QT-MP3W Special notes WARNINGS When the FUNCTION switch is set at TAPE/STAND-BY position, mains voltage is still present inside the unit. This unit contains no user serviceable parts. [. . . ] (Sampling Frequency is 32, 44. 1, 48kHz) "MPEG-2 Audio Layer-3", "MPEG-2. 5 Audio Layer-3" and MP1, MP2 format are not supported. Playback order for MP3 files may differ sometimes depending on the writing software used during file download. Bitrate which is supported by MP3 is 32~320 kbps, WMA is 64~160 kbps. For MP3/WMA files, please put ". MP3" ". WMA" extension. Files cannot be played back if there is no MP3/WMA extension. Playlists are not supported on this unit. Copyright protected WMA files cannot be played back. FOLDER Folder number Whilst in the stop mode, press the MEMORY button to enter the programmed save mode. Select a track by pressing the FOLDER ( or ) button to desire folder. Press the or button to select the desire track. MEMORY MEMORY 3 FOLDER MEMORY Folder number MEMORY Track number 4 Press the MEMORY button to save the track number. MEMORY 5 Repeat steps 2 - 3 for other tracks and programmed number will automatic increase. "_ _ _" indicator will display on LCD after programmed up to 20 tracks. If you make a mistake, the programmed tracks can be cleared by pressing the button twice. Press the / button to start playback. 6 10 CD or MP3/WMA disc Playback 2 QT-MP3W MP3/WMA folder mode (only for MP3/WMA files) To playback MP3/WMA (Windows Media Audio) file There are many music sites on the internet that you can download MP3/WMA (Windows Media Audio) music files. Follow the instructions from the website on how to download the music files. You can then playback these downloaded music files by burning them to a CD-R/RW disc. Your downloaded song/files are for personal use only. Any other usage of the song without owner's permission, is against the law. Procedure to playback MP3/WMA disc To playback CD-R/RW. 1 Press the OPEN button, and load a MP3/WMA disc. After disc is loaded, the disc info will be displayed. FOLDER CD or MP3/WMA disc Playback About folder playback order If MP3/WMA files are recorded in several folders, only total folder will be display. The folder and file order information which is recorded on the disc depends on the writing software. There maybe possibilities that this unit will playback the files not according to our expected playback order. Total folder 2 Whilst in stop or play mode, press the FOLDER ( button to select desired playback folder. FOLDER Indicator FOLDER or ) FOLDER Number 3 Select desired track to be played back by pressing the or button. 4 5 Whilst in stop mode, press the Playback will start. To stop playback, press the / button. button. 11 Listening to the radio TUNING ON QT-MP3W / VO LUME TU NING ·M IN X· MA MHz 108 X-BASS KHz 1600 1400 106 104 1200 1000 800 700 96 ON OFF TAPE (STAND-BY) CD RADIO FUNCTION MIC PU 102 100 SH /C LO SE · AM · FM 600 92 90 88 530 AM BAND EN OP FM 1 2 3 4 Set the FUNCTION switch to RADIO. Set the BAND SELECTOR switch to FM or AM. [. . . ] Possible cause Is the unit placed near the TV or computer?Move the aerial away from the AC power lead if it's located nearby. If trouble occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc. ) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on. 16 References QT-MP3W Troubleshooting chart (continued) Before transporting the unit Remove CD from the unit. [. . . ]