User manual SHARP QT-CD110H

[. . . ] Quick stops, excessive force and uneven surfaces m ay cause the appliance and cart combination to overturn. The lightning flash with arrow head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. An exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. IMPORTANT SAFEGUARDS continued connection a la terre ne manque pas. Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. [. . . ] Recalling a FAVORITE Channel 35 34 QT-CD110HXM MANUAL INTRODUCTION TO XM SATELLITE RADIO continued To recall a FAVORITE channel from the "A" or "B" lists, there are several methods that can be used. · The first method is to press `A' or `B' followed by a single numeric number within 5 seconds. The receiver will immediately go to that favorite. It is not necessary to press the `ENTER" softkey. For example: `A', `4' · The second method is to press the `A' button, and use the `TUNING' knob to scroll through the entries in both "A" and "B" lists until you reach the channel you wish to recall. Then press `ENTER' for immediate entry, or if "AUTO ENTER" is enabled in the "XM" menu, simply wait the programmed number of seconds and the recalled channel will be entered automatically. · The third method is to press the `FAVORITES' softkey, and as above, use the `TUNING' knob to scroll through the entries on the "A" and "B" lists until the desired entry is reached. Then press `ENTER' for immediate entry, or if `AUTO ENTER' is enabled in the "XM MODE" menu, simply wait the programmed number of seconds and the recalled channel will be entered automatically. Deleting a FAVORITE Channel To delete a FAVORITE channel proceed as follows: · Select the favorite channel to be deleted. This will cause the notation "PRESS A OR B TO DELETE" to appear on the display. · Press "A" or "B" as appropriate. This would be either the VFO, MEMORY, COUNTRY, or XM display. RADIO SETTINGS The radio settings menu is reached either by pressing the MENU softkey twice, or by pressing `1' when the MAIN MENU is displayed. It appears as shown below. 36 37 QT-CD110HXM MANUAL QT-CD110H MENUS continued 1. ENHANCED SSB OFF / ON - Pressing `1' toggles ENHANCED SSB ON and OFF. Enhanced SSB provides 30 Db of additional rejection of the undesired sideband through audio phasing circuitry, as shown in the following diagram. QT-CD110H MENUS continued AUDIO SETTINGS The AUDIO SETTINGS menu is reached either by pressing the MENU softkey three times, or pressing the MENU softkey once and then pressing the `2' key. It appears as shown in the following illustration. Using this in combination with passband tuning can narrow the IF to less than the normal IF filter bandwidth, and can provide considerable additional help in receiving weak signals in the presence of strong adjacent signals. SCAN STOP MODE TIME / CARRIER - The `2' key toggles between TIME and CARRIER. When "TIME" is selected, a T. SCAN will stop on each MEMORY, COUNTRY, or XM channel that is marked with a "T" for 5 seconds, and will then move on to the next marked channel. If CARRIER is selected, a T. SCAN will stop on a carrier that exceeds the SQUELCH setting and will remain there as long as the carrier strength remains at that level. If the carrier goes away, or if its strength drops below the squelch setting, the T. SCAN will move on to the next marked channel. FM 76 - 90 MHz / 87 MHz - 108 MHz - Pressing `3' toggles the frequency coverage on FM mode between 76 90 MHz and 87 - 108 MHz. [. . . ] Enable the timer with the instructions provided below. USING TIMER 2 AS A SLEEP TIMER Sequentially press the MENU key to display the TIMERS MENU. Use the `4' key to select the turn-on time and clear any entry in this window using the CLEAR/LOCK and STORE keys as described above. Press the `5' key to set a turn-off time as in the example above. [. . . ]