User manual SHARP QTCD220 OPERATION MANUAL

[. . . ] TO <P=001> PORTABLE CD STEREO SYSTEM MODEL QT-CD210H QT-CD220H OPERATION MANUAL Thank you for purchasing this SHARP product. For the best performance, read this manual carefully. It will guide you in operating your SHARP product. NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. [. . . ] Removing the tab will protect the corresponding side from being erased. Cover the tab holes with adhesive tape to erase or record again. Side A (1) s Care of compact discs Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player. q Do not write on either side of the disc, particularly the non-label side. Signals are read from the non-label side. q Keep your discs away from direct sunlight, heat, and excessive moisture. Fingerprints, dirt, or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius. Tab for side B (2) Tab for side A (1) NAMES OF CONTROLS AND INDICATORS 1 2 34 5 6 7 8 9 11. 22. 2 (TAPE) Record Button (TAPE) Play Button (TAPE) Rewind Button (TAPE) Fast Forward Button (TAPE) Stop/Eject Button (TAPE) Pause Button Cassette Compartment CD Compartment CD Eject Button Tuning Control (CD) Stop Button (CD) Track Down/Review Button Volume Control Stand-by, On/Function Switch (CD) Track Up/Cue Button (CD) Play/Pause Button (CD) Play Indicator (CD) Pause Indicator Battery Compartment FM Telescopic Rod Aerial Headphone Socket AC Power Input Socket 10 11 12 13 17 18 14 15 16 19 20 21 22 QT-CD210H(SUK) TINSE0034SJZZ <P=003> POWER SOURCE s AC power Precautions for battery use: q Insert the batteries according to the direction indicated on the rear panel. q Replace all old batteries with new ones at the same time. q Remove the batteries if they are weak or if the unit will not be used for long periods of time. This will prevent potential damage due to battery leakage. Caution: q Do not use rechargeable batteries (nickel-cadmium battery, etc. ). Battery replacement: Replace the batteries when they become weak and/or recording or playback is impaired. This may occur even though radio broadcasts are audible. To AC INPUT AC 230-240 V, 50 Hz To an AC socket Connect the AC power lead to the AC power input socket, then connect the AC power lead plug to an AC socket. Notes: q If the unit will not be used for a long period of time, remove the AC power lead from the AC socket. q Connection of the AC power lead to the unit disconnects the batteries. q Never use a power lead other than the one supplied. Use of a power lead other than the one supplied may cause an electric shock or fire. RADIO OPERATION s Battery power ON/STAND-BY (Function) TUNING 1 2 2 3 1 Set the function switch to AM or FM. Use the TUNING control to tune in to the desired station. q During FM stereo reception, it automatically switches to monaural when the signal is weak. Aerial adjustment FM AM 5 6 4 1 2 Disconnect the AC power lead, and remove the battery compartment cover. [. . . ] q Tune in to the station to be recorded. Load a blank cassette into the cassette compartment. Press the PAUSE button again. To stop recording: Press the STOP/EJECT button. s Erasing a recorded tape 1 2 3 Set the function switch to TAPE. Load the tape to be erased into the cassette compartment. [. . . ]