User manual SHARP RK-T11 OPERATION MANUAL

[. . . ] If you have any comments or concerns about the manual, please contact your nearest SHARP Service Department. • This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest SHARP Service Department. • Aside from instances provided for by law, SHARP is not responsible for failures occurring during use of the product or its options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due to use of the product. The display screens, messages, and key names shown in the manual may differ from those on the actual machine due to product improvements and modifications. PRODUCT CONFIGURATIONS This product series consists of the models indicated below. [. . . ] To delete a digit, move the cursor to the digit that you wish to delete with the [ ] or [ ] key and then press the [C] key. 2 Press the [OK] key. 7 Press the [OK] key. OK BACK OK GHI 8 3 Select "CHANGE" with the [ ] or [ ] key. 26 A Edit the name of the destination (see "ENTERING CHARACTERS" on page 82). 27 B 28 C 29 D 30 E 31 32 F G 33 H 34 I 35 J ENTER NAME ABCDE ABC RAPID/SPEED CHANGE DELETE 36 K 37 L 38 M 39 N 40 O 9 4 Press the [OK] key. OK Press the [OK] key. OK 10 5 26 A Edit the search characters (see "ENTERING CHARACTERS" on page 82). 27 28 B C Press a Rapid key ([01] to [50]) or the [SPEED] key. 26 A 29 D 30 E • To edit a Rapid key, press the Rapid key that you wish to edit ([01] to [50]). 27 B 31 F 32 G 33 H 34 I 35 J KEY WORDS ABCDE ABC 36 K 37 L 38 M 39 N 40 O 28 C 29 D 30 E [START]:ENTER 31 F 32 G 33 H 34 I 35 J 36 K 37 L 38 M 39 N 40 O Characters added in step 8 will appear at the end of the previously stored search characters. (Maximum of 10 characters altogether. ) 68 PROGRAMMING 11 To finish the storing procedure, press the [START] key ( ). If you wish to program an option such as F-code, chain dialling, transmission speed, or international transmission mode, press the [OK] key. • If you pressed the [START] key ( ), go to step 5. If you wish to program another Rapid key or Speed Dial number, repeat steps 5 to 11. Editing to that point will be completed. • If you pressed the [OK] key, go to the appropriate page for the option that you wish to edit. To program F-code settings, follow the steps in "F-code settings" on pages 64 and 65. To select "CHAIN DIAL", go to "Chain Dialling" on page 65. To set the "TRANSMISSION SPEED", go to "Transmission speed setting" on page 66. To set the "INTERNATIONAL TRANSMISSION MODE", go to "International transmission mode setting" on page 66. 3 Select "DELETE" with the [ ] or [ ] key. SBC CO. DELETE NO DELETE [#]:DETAIL Note If you select "NO DELETE", you can press the key to check the destination name. A program name must be entered. 9 Press the [OK] key. 72 PROGRAMMING 10 Select the program that you wish to store with the [ ] or [ ] key. 8 PROGRAM TX TYPE SENDING MENU [ ]:CANCEL [START]:ENTER • A transmission method, cover sheet/message, resolution/exposure settings, dual pages, sender's name, and transmission settings can be stored. The storing procedure cannot be completed unless a transmission method is stored. • For the procedures for selecting each of the settings, refer to the explanations of the settings. • To cancel a setting selection, select the setting that you wish to cancel and then press the key. • Some settings cannot be used in combination with others. If you select a prohibited combination of settings, a message will appear in the display. Edit the program name (see "ENTERING CHARACTERS" on page 82). • See step 8 of "STORING A PROGRAM". • If you do not wish to edit the program name, go to the next step. 9 10 Press the [OK] key. Select the stored setting that you wish to edit with the [ ] or [ ] key. • See steps 10 and 11 of "STORING A PROGRAM". • If you do not wish to edit the stored settings, press the [START] key ( ) and then press the [BACK] key to exit. [DELETING PROGRAMS] Before deleting a program, print the "PROGRAM LIST" to check the contents. (Page 81) To delete a previously stored program, follow these steps: 11 To continue selecting another setting, press the [OK] key. When you have finished selecting settings, press the [START] key ( ). If you wish to store another program, repeat steps 8 to 11. [. . . ] If you do not have Acrobat Reader, follow the steps below to install it. Windows environment Macintosh environment 1 2 Insert the CD-ROM into the CD-ROM drive. Click the [Start] button, click [My Computer] ( ), and then double-click the [CD-ROM] icon ( ). In Windows 95/98/Me/NT 4. 0/2000, double-click [My Computer] and then double-click the [CD-ROM] icon. 1 2 3 4 Insert the network expansion kit "Software CD-ROM (1)" into your computer's CD-ROM drive. Double-click the [CD-ROM] icon ( on the desktop. Double-click the [Acrobat Reader] folder and then double-click the [English] folder. [. . . ]