User manual SHARP RP-116E

[. . . ] If using countertop with integrated drip edge, remove 3/4" to clear 31 1/2" width control panel as illustrated. 3/4" min. 31 1/2" R 3/8" minimun flat area 30" 13" max 30" to bottom of cabinet over cooktop 3/8" minimun flat area 30" cutout 18" to upper cabinets 25" countertop depth 22 7/8" cutout 22 7/8" 23 1/2" min depth Allow 7/16" product overlap 30" opening width 6" 15" ±1/8" vertical opening 16 5/8" min to any obstruction behind cabinet face Figure 3 36" countertop height To eliminate the risk of burns or fi re by reaching over the cooktop, cabinet storage space located above the cooktop should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets. 6" Preferred junction box location Figure 2 2 INSTALLATION MANUAL IMPORTANT NOTES TO THE INSTALLER · Read all of the Installation Manual before installing the appliance. · Remove all packing material from the drawer and cooktop before connecting the electrical supply to the appliance. · Observe all governing codes and ordinances. [. . . ] · The installation of appliances designed for manufactured (mobile) home installation must conform with Manufactured Home Construction and Safety Standard, title 24CFR, part 3280 [Formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD (part 280)] or when such standard is not applicable, the Standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups), ANSI Z225. 1/NFPA 501A- latest edition, or with local codes in United States. · Make sure the wall coverings and the cabinets around the appliance can withstand the heat generated by the appliance. Never leave children alone or unattended in the area where an appliance is in use. As children grow, teach them the proper, safe use of all appliances. Stepping, leaning or sitting on the drawer of this appliance can result in serious injuries and can also cause damage to the appliance. · Do not store items of interest to children in the cabinets above the appliance. Children could be seriously burned climbing on the appliance to reach items. · To eliminate the need to reach over the cooktop, cabinet storage space above the cooktop should be avoided. · Do not use the drawer as a storage space. This creates a potentially hazardous situation. Tilt the appliance as you slide it back so that it will clear. The unit will have to be pushed in until the front feet are behind the cabinet face frame. See Figure 11. Confirm that the slots on the mounting bracket have engaged the stop screws. See Figure 14. Figure 14 If the cooktop does not fit properly on the counter top, the mounting bracket may not be positioned properly on the stop screws. To correct, slide the appliance out one inch and follow instructions from F above. Figure 11 5 INSTALLATION MANUAL I MAKE SURE THE EDGE OF THE COUNTERTOP FITS FLUSH AGAINST THE END OF THE FRONT CONTROL PANEL. See Figure 15. National Electrical Codes, ANSI/NFPA No. 70-Latest Edition. Effective January 1, 1996, the national Electrical Code requires that new, but not existing, construction utilize a four-conductor connection for this appliance class. When installing this appliance in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, follow the instructions in the section on NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTOR. ELECTRICAL SHOCK HAZARD · Electrical ground is required on this appliance. · Do not connect to the electrical supply until appliance is permanently grounded. Figure 15 · DISCONNECT POWER TO THE CIRCUIT BREAKER OR FUSE BOX BEFORE MAKING THE ELECTRICAL CONNECTION. CHECKING INSTALLATION To check if the device is installed and engaged properly, open the Microwave Drawer fully and gently apply medium force in the center of the handle until movement of the appliance is detected. Continue pressing until the Anti-Tip bracket is engaged and movement stops. A small amount of movement is acceptable at the back of the appliance top, but it should be stable and not tip once the Anti-tip bracket is engaged. Stop pressing on the Microwave Drawer handle and close. · This appliance must be connected to a grounded, metallic, permanent wiring system or the grounding connector of the power cord should be connected to the grounding terminal or wire lead on the appliance. [. . . ] Breaker or fuse size: 240V 208V 40 Amps 40 Amps Rating plate Figure 16 All electrical wiring and hookup for this appliance should be by a qualified electrician. Be familiar where the main appliance disconnect is located. Check with local utilities for electrical codes which apply in your area. Failure to wire your appliance according to governing codes could result in hazardous conditions. [. . . ]