User manual SHARP RP-15HB

[. . . ] Check that the floor covering is smooth and flat and that it adheres to the sub-floor solidly. · Provide adequate clearances between the range and adjacent combustible surfaces. To eliminate the risk of burns or fire by reaching over the cooktop, cabinet storage space located above the cooktop should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets. IMPoRtant notEs to thE InstallER · Read all of the Installation Manual before installing the range. · Remove all packing material from the oven and drawer before connecting the electrical supply to the range. [. . . ] Cord must have either 3 or 4 conductors to match electric receptacle. The power cord kit is not included so must be purchase at an appliance store. For mobile homes, new installations, recreational vehicles or areas where local codes do not permit grounding through neutral, a 4 conductor power supply cord kit rated at 240 volts or 208 volts minimum, 50 amperes and marked for use with ranges should be used. Terminals on end of wires must be either closed loop or open-end spade lugs with upturned ends. The range connection opening should be 1 3/8-inches. To reduce the risk of tipping the range, it must be secured by properly installed Anti-Tip bracket packed with the range. · This range must be electrically grounded in accordance with local codes, or in their absence, with the National Electrical Code ANSI/NFPA No. 70--latest edition in United States. · The installation of ranges designed for manufactured (mobile) home installation must conform with Manufactured Home Construction and Safety Standard, title 24CFR, part 3280 [Formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD (part 280)] or when such standard is not applicable, the Standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups), ANSI Z225. 1/NFPA 501A- latest edition, or with local codes in United States. · Make sure the wall coverings and the cabinets around the range can withstand the heat generated by the range. InstallatIon Manual Risk of fire or electrical shock exists if an incorrect size range cord kit is used, or the installation instructions are not followed precisely and/or a strain relief clamp is not used. Do not loosen the nuts which secure the factory-installed range wiring to the terminal block while connecting range. Electrical failure or loss of electrical connection may occur. electRIcal shock hazaRd & -wIRe electRIcal wall Receptacle types & RecoMMended MountIng oRIentatIon on wall Figure 5A illustrates 4-wire receptacle required for new and remodeled installations. IMpoRtant DO NOT LOOSEN the factory installed nut connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed. Strip insulation away from the ends of the permanent wiring for line 1, line 2 and neutral; also strip ground wire on 4-wire connections. Tighten all 3 or 4-wire leads to the terminal block. Follow wire locations shown in Figure 10. A ground strap is installed on this range which connects the center terminal of the neutral terminal block to the range chassis. The ground strap is connected to the range by the center, lowest screw. The ground strap must not be removed unless National, State or Local Codes do not permit use of a ground strap. note: If the ground strap is removed for any reason, a separate ground wire must be connected to the separate ground screw attached to the range chassis and to an adequate ground source. connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed. note: For 3-wire permanent connection skip steps 3 and 4 and continue with step 5. IMpoRtant DO NOT LOOSEN the factory installed nut Disconnect the ground strap. Remove the factory installed ground screw and plate to release the factory installed copper ground strap from frame of the range. Cut and discard the copper strap from the terminal block. KEEP the ground screw, ground plate and go to step 4. Make sure all connections are tightened securely and replace the rear access cover and secure with screw. See Figure 6. -wIRe connectIon Note: Install strain relief clamp. [. . . ] Measure from the floor to the top of the cooktop glass (X) and adjust the legs to match the measurement (Y) taken from the cutout. See Figure 16. Lock Nut (Rear leg only) 1 5/8" to edge of bracket Range Slide (Y") floor to top of countertop (X") floor to top of cooktop glass Figure 8 Figure 6 · After leveling, tighten the lock nuts on the rear to prevent the feet from turning when sliding into position. See Figure 17. Figure 7 7 InstallatIon Manual Refer to the Operation Manual for cleaning instructions. If removing the range is necessary for cleaning or maintenance, disconnect the electrical power supply. [. . . ]