User manual SHARP SD-SH111

[. . . ] 1-BIT DIGITAL RECEIVER WITH DVD AMPLI TUNER NUMÉRIQUE 1-BIT AVEC DVD SD-SH111 OPERATION MANUAL MODE D'EMPLOI ENGLISH Please refer to pages i to iv and E-1 to E-70. FRANÇAIS Se reporter aux pages iv et F-1 à F-70. SDSH111U_FRONT 1 02. 11. 20, 2:44 PM SPECIAL NOTES (for Users in the U. S. A. ) NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Playback does not start if a chapter number higher than that selected. on the disc is 1 2 During playback, press the DIRECT button 3 times. Within 10 seconds, specify the time with the direct buttons (0 - 9) and then press the ENT button. 2/5 10 / 30 : : To resume playback after stopping (sequential playback) 1 2 3 While the disc is playing, press the DVD/CD The system stores the point you stopped. button. 2/5 10 / 30 01 : 23 :40 To restart play, press the DVD/CD Play resumes from the point you stopped. button. button twice. To specify 1 hour 23 minutes and 40 seconds, enter "012340". If you enter the wrong number, press the CLEAR button and then reenter. If the time is entered with the or buttons while setting the time, press the or buttons to switch between hours, minutes, and seconds. To cancel this operation, press the DVD/CD Notes: The sequential playback feature is disabled on some discs. Depending on the disc, playback may resume from slightly before the stopped position. To start playback from the beginning, cancel this operation. Opening the disc compartment will cancel the sequential playback operation. Note: Playback does not start if you specify the time exceeding the actual recording time. - Basic operation - To play by specifying time: Advanced Disc Features If you enter the wrong number, press the CLEAR button and then reenter. You can also select the chapter number by pressing the or button. 7 E-34 02/11/20 SD-SH111(U)E4. fm SD-SH111 Useful features You can play back the desired titles (tracks) or chapters in the sequence you want. Maximum of 20 titles (tracks) or chapters can be programmed. ENGLISH [Back] To play in the desired order (programmed playback) To play in the desired title (track) order: Example: To enter the 12th title on a DVD 1 While stopped, press the PROGRAM button. The programming screen is displayed. Advanced Disc Features T I T L E P ROGR AM L ANGU AGE : T = T I T L E T- T- T- T- T- T- T- T- T- T- T- T- - 2 Use the or button to select the desired title (track) number, and then press the ENT button. T I T L E P ROGR AM T12 T- T- T- T- T- T=T I TLE T- T- T- T- T- T- - - Useful features - The cursor moves to the next position when programming is completed. Repeat the procedure above if you want to enter other title numbers. You can enter up to 20 titles in the sequence you want to play. If you enter the wrong number, press the CLEAR button and then reenter. 3 Press the button to start play. The unit stops after playing the tracks in the programmed order. The program content will be stored in the memory. To change the programmed contents: Repeat the above procedures from step 1. E-35 02/11/20 SD-SH111(U)E4. fm SD-SH111 ENGLISH To play chapters in the desired sequence within a title: Notes: You can also select the title (track) or chapter number by pressing the 0 - 9 buttons. Programming cannot be performed while paused or in the playback mode. Sequence programming does not work with a disc that does not include title or chapter information. Sequence programming does not work with a disc that disables programming. The number you enter is not stored in memory if there is no corresponding title (track) or chapter number on the disc. To exit the programming procedure halfway through, press the RETURN button. Once programmed, the contents will be memorized until they are changed or the disc is removed. To perform programmed playback with the same disc, press the PROGRAM button and start playback. [. . . ] A title is one movie on a DVD on which more than one movie are recorded. The menu recorded on a DVD, where you can select the title to be played. Dolby Pro Logic II When playing a stereo-recorded disc or video tape, the Dolby Pro Logic II function converts the sound to the 5. 1ch digital sound automatically. More natural sound effect can be achieved. Track Each one of multiple tunes that are recorded on a CD. DTS One of the digital audio systems for theatrical use. As the sound quality is emphasized, you can enjoy the realistic sound effect in the home theater system. Virtual Although no sound is heard from the surround speakers, you can still enjoy the 2. 1ch surround sound as if they exist. GAMMA Corrects gradations in dark areas of images to make them clearer. Zoom You can enlarge the size of the displayed image. - Glossary - Top menu References 7 E-70 02/11/20 SD-SH111(U)E7. fm VALID IN U. S. A. ONLY CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. [. . . ]