User manual SHARP SDCX1 OPERATION MANUAL

[. . . ] 1-BIT DIGITAL AUDIO SYSTEM SD-CX1H OPERATION MANUAL Special Notes NOTES FOR USERS IN THE U. K. AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. [. . . ] If you want to redo the ASPM operation, erase the preset memory. If the RDS signals are very weak, station names may not be stored in memory. 1 Using the Radio Data System (RDS) Press the TUNER (BAND) button to select the FM band. To erase all of the contents of preset memory: 2 Press and hold down the ASPM button for at least 3 seconds. 1 2 3 RDS Radio After "ASPM" has flashed for about 4 seconds, scanning will start (87. 50 - 108. 00 MHz). Press the TUNER (BAND) button. Hold the CLEAR button down for 3 seconds or more. Press the ENTER button. When an RDS station is found, "RDS" will appear for a short time and the station will be stored in memory. To store a station name again if the wrong name was stored in memory: It may be impossible to store station names in memory using the ASPM function if there is lots of noise or if the signal is too weak. PRESET or button to check whether the names are correct. If you find a wrong name during receiving the station. Wait until the correct name will be displayed. PRESET or button to display the preset channel to be corrected again. 4 Within 5 seconds, press the ENTER button. The new station name has been stored in memory correctly. Notes: The same station name can be stored in different channels. In a certain area or during certain time periods, the station names may temporarily be different. 1 2 After scanning, the number of stations stored in memory will be displayed for 4 seconds, and then "END" will appear for 4 seconds. 30 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) To recall stations in memory To specify programme types and select stations (PTY search): You can search a station by specifying the programme type (news, sports, traffic programme, etc. see page 29) from the stations in memory. 1 Press the TUNER (BAND) button to select the FM band. Notes: If the display has stopped flashing, start again from step 2. If the unit finds out a desired programme type, corresponding the station name will flash for 10 seconds and remain lit. If you want to listen to the same programmed type of another station, press the PTY-TI button whilst the channel number and station name are flashing. The unit will look for the next station. If no station can be found, "NOT FOUND" will appear for 4 seconds. If you select the traffic programme: If you select the traffic programme (TP) in step 4, "TP" will appear. (This does not mean that you can listen to the traffic information at that time. ) When a traffic information is broadcast, "TA" will appear. "PTY TI" and "SELECT" will appear alternately for about 6 seconds. 3 Within 6 seconds, press the TUN. PRESET the programme type you want. or button to select You can select a station by specifying the name (BBC R1, BBC R2, etc. ) from the stations stored in memory. Before starting this operation, you must store one or more station names in memory. 1 Press the TUNER (BAND) button to select the FM band. [. . . ] Then, set the unit to the power stand-by mode. Carrying the unit with discs left inside can damage it. Condensation Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) References Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, MD pickup, etc. ) or on the transmitter on the remote control. Condensation can cause the unit to malfunction. If this happens, leave the power on with no disc in the unit until normal playback is possible (about 1 hour). [. . . ]