User manual SHARP SF-2010

[. . . ] Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code below. [. . . ] As an example, the paper in tray 1 is changed from B4 (8-1/2" x 14") size plain paper to A4 (8-1/2" x 11") size recycled paper. Gently pull out the paper tray. If paper remains in the tray, remove it. Move the two guides on the tray. For example, move the guides from B4 (8-1/2" x 14") to A4 (8-1/2" x 11"). Insert the paper with the print side face up. Otherwise, multiple sheets may feed at once and cause a misfeed. Insert the paper and then gently push the tray into the machine. Indicator line The indicator line indicates the maximum height of the paper that can be loaded in the tray. When loading paper, make sure that the stack is not higher than the indicator line. Do not load as shown below. 22 LOADING PAPER IN A TRAY Changing the tray settings When you change the paper in a tray, the tray settings in the system settings must also be changed. 1 SYSTEM SETTINGS Press the [SYSTEM SETTINGS] key. 2 System Settings Admin Password Exit Total Count Default Settings List Print (User) Fax Data Receive/Forward Configure the tray settings in the touch panel. (1) Touch the [Paper Tray Settings] key. Paper Tray p Settings Printer Condition Settings Address Control (1) Document Filing Control USB-Device Check System Settings Paper Tray Settings Back (2) Touch the [Tray Settings] key. Tray Settings Paper Type Registration Auto Tray Switching Custom Size Registration (Bypass) (2) Tray Settings Back (3) Touch the [Change] key in "Tray 1". Tray 1 Type Size Plain Change B4 Paper Property Fixed Paper Side Disable Duplex Disable Staple (3) Disable Punch I-Fax Doc. Filing Feeding Approved Job Copy Print Fax System Settings Tray Settings Tray: Type: Size: Tray 1 Recycled Auto-AB A3, A4, A4R, B4, B5, B5R, 216x330(8 1/2x13) Paper Property: Print Copy I-Fax Fax Cancel OK (6) (4) (5) (4) Select [Recycled] from the "Type" select box. (5) Make sure that [Auto-AB] is selected in the "Size" select box. For more information, see "Paper Tray Settings" in "7. SYSTEM SETTINGS" in the Operation Guide. (6) Touch the [OK] key. The above steps change the paper settings for tray 1 to A4 recycled paper. 23 LOADING PAPER IN A TRAY Loading paper in other trays Bypass tray The side to be copied on must be face down! When loading A3W, A3 or B4 size paper, pull out the tray extension. The maximum number of sheets that can be loaded in the bypass tray is approximately 100 for plain paper and approximately 20 for envelopes. Example: Loading an envelope Place paper that is A5 (7-1/4" x 10-1/2") or smaller in the horizontal orientation. Only the address side of envelopes can be printed on. INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER (page 31) · Scanner driver (TWAIN driver) (can only be used when the machine is connected to a network) This allows you to use the scanner function of the machine from a TWAIN-compliant software application. INSTALLING THE SCANNER DRIVER (page 1-100 in the Operation Guide) OTHER CD-ROMS "PRINTER UTILITIES" CD-ROM that accompanies the PS3 expansion kit (for Windows/Macintosh) This contains the display fonts that are used with the PS printer driver. (Install the PS printer driver and Macintosh PPD file from the "Software CD-ROM". ) INSTALLING THE PS DISPLAY FONTS (page 1-102 in the Operation Guide) "PRINTER UTILITIES" CD-ROM that accompanies the Internet fax expansion kit (for Windows) This CD-ROM is used to update the PC-Fax driver on the "Software CD-ROM" so that it can be used to send Internet faxes (PC-I-Fax function). If you wish to use the PC-I-Fax function, first install the PC-Fax driver from the "Software CD-ROM" and then run the installer on this CD-ROM. If the PC-Fax driver is already installed, run only the installer. (There is no need to reinstall the PC-Fax driver. ) INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER (page 31) "Sharpdesk/Network Scanner Utilities" CD-ROM (for Windows) This contains software that helps you get the most out of the images that you scan on the machine. The software includes "Sharpdesk", a desktop document management application that enables integrated management of scanned images and files created using a variety of applications. To use the "Scan to Desktop" scanner function, the "Network Scanner Tool" must be installed from the CD-ROM. For the system requirements of the software, see the manual (PDF format) in the "Manual" folder or the Readme file on the CD-ROM. For the procedures for installing the software, see the "Information Guide". 27 BEFORE INSTALLING THE SOFTWARE VERIFYING SYSTEM REQUIREMENTS SYSTEM REQUIREMENTS Before installing the software described in this manual, make sure that your computer satisfies the following requirements. Windows*1 Operating system Windows 2000 Professional, Windows XP Professional*2, Windows XP Home Edition, Windows 2000 Server, Windows Server 2003*2, Windows Vista*2, Windows Server 2008*2, WIndows 7*2*3 IBM PC/AT compatible computer Equipped with a 10Base-T/100Base-TX/1000Base-T LAN board or equipped standard with a USB 2. 0/1. 1*3 port. [. . . ] · Sharp OSA is a trademark of Sharp Corporation. · RealVNC is a trademark of RealVNC Limited. · All other trademarks and copyrights are the property of their respective owners. Candid and Taffy are trademarks of Monotype Imaging, Inc. [. . . ]