User manual SHARP SF-2530

[. . . ] SF-2530 MODEL SF-2530 PLAIN PAPER COPIER PLAIN PAPER COPIER OPERATION MANUAL ·GETTING STARTED ·MAKING COPIES · STATUS INDICATORS ·GENERAL INFORMATION ·OPTIONAL EQUIPMENT Page 2 8 22 30 53 llllllllllllll llllllllllllllllllllllllllllllllllllllll lllllllllllll The power switch positions are marked "I" to indicate power "ON" and " " to indicate stand-by. In the stand-by position, power is being supplied to a drying heater within the optical system of the copier. Caution: For complete electrical disconnection, pull out the main plug. The equipment should be installed near an accessible socket outlet for easy disconnection. ¢¢¢¢¢¢¢¢¢¢¢¢ ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢ lllllllllllllllllllllllllllllllllllllll ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢ ¢¢¢¢¢¢¢¢¢¢¢¢¢ FOR YOUR RECORDS . . . To protect against loss or theft, record and retain for reference the copier's serial number located on the right hand side at the rear bottom corner of the copier. [. . . ] For setting of all programs, first follow steps 1 and 2 in "Auditing code number" on page 37. (Press the clear ( C ) key, the INTERRUPT key, and the clear key again. Enter the auditor code number using the 10-key pad. ) Then enter the program number using the 10-key pad and press the START key. Follow the appropriate instructions for the program. 38 AUDITING PROGRAMS Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. A maximum of 49, 3-digit account numbers can be assigned. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display. 1. Select the desired setting using the 10-key pad. 1 4 7 0 2 5 8 C 3 6 9 POWER SAVE START 0: 1: OFF ON 2. Press the START key. q The setting will be stored. 3. To continue with other auditing programs, enter the desired program number. 11 is entered, "­­" will appear in the copy quantity display. q If the number of accounts has reached the upper limit (49), "1E" will appear in the copy quantity display for approximately 5 seconds. Enter another program number or press the key to exit the auditing program. GENERAL INFORMATION 1 4 7 0 2 5 8 C 3 6 9 POWER SAVE 1. Enter a 3-digit account number using the 10-key pad. q START Any 3-digit number except "000" and the auditor code number can be registered as an account number. 2. Press the START key. q If a number that is already registered or "000" is entered, the number will blink in the copy quantity display for approximately 5 seconds. Then, "­­" will appear again to prompt account number entry. Auditing programs 3. Repeat steps 1 and 2 for other account numbers. To continue with the other auditing programs, press the INTERRUPT key and then enter the desired program number. To exit the auditing program mode, press the key. 39 AUDITING PROGRAMS Program No. 12 is entered, an account number will appear in the copy quantity display. q If no account number has been registered, "2E" will appear in the copy quantity display for approximately 5 seconds. Enter another key to exit the auditing program. [. . . ] Do not load paper above the maximum height line. q Push the paper drawer firmly back into the copier. 83 STAND/500-SHEET PAPER DRAWER (SF-D20)/STAND/1000-SHEET PAPER DRAWER (SF-D21) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink and blinking red misfeed location indicators will indicate the approximate misfeed location. 1 Open the side cover and remove any misfed paper. q Be sure to perform this step before pulling out either of the paper drawers. If not, the paper may be torn as a drawer is opened. Be sure not to tear the misfed paper during removal. q 2 Stand/500-sheet paper drawer (SF-D20) Stand/1000-sheet paper drawer (SF-D21) OPTIONAL EQUIPMENT Gently lift and pull out the paper drawer. [. . . ]