User manual SHARP SF2052 OPERATION MANUAL

[. . . ] MODEL SF-2052 ELECTROSTATIC COPYING MACHINE OPERATION MANUAL · GETTING STARTED 2 · MAKING COPIES 7 · SUPPLIES 48 · COPIER TROUBLE?53 · GENERAL INFORMATION 66 · OPTIONAL EQUIPMENT 75 · KEY OPERATOR'S GUIDE 105 Page CONTENTS GETTING STARTED q q q q q q Page GETTING STARTED INTRODUCTION . . 2 2 3 3 4 5 6 MAKING COPIES q q q q q q q q q q q q q q AUDITING ACCOUNTS . . 7 8 12 14 16 17 18 19 21 24 26 43 45 47 MAKING COPIES SUPPLIES SUPPLIES q q q PAPER . [. . . ] @3 Original size display The original paper size is displayed. @4 TRAY SELECT key Press to select the desired paper tray. Initial settings The copier assumes the initial settings when the CLEAR ALL ( ) key is pressed and approximately 1 minute (auto clear time) after the last copy is made in any mode. Except for the paper tray selection, the copier also assumes the initial settings when it is turned on. q Copy ratio: 100% q Automatic exposure q Copy quantity: 0 q All special copier modes are set to off. q Tray select: Tray 1 or an optional large capacity tray (when installed) (At power on, the previously selected tray will again be selected. ) 5 KEY OPERATOR Initial settings can be programmed as desired. The auto clear time can also be changed. See pages 119 and 117. Part locations and functions 69 USER MAINTENANCE The document glass and RADF transport belt must be kept clean to avoid dirty areas from being copied onto the copies. Document glass and RADF transport belt Wipe the document glass and transport belt with a soft, clean cloth. q If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. GENERAL INFORMATION User maintenance 70 MAINTENANCE REQUIRED When the message "READY TO COPY. (MAINTENANCE REQUIRED : )" appears, service by an authorised Sharp Service Technician will be required soon. Contact your Service Centre as soon as possible. GENERAL INFORMATION Maintenance required 71 SPECIFICATIONS COPIER Type Copy system Originals Original feed system Original size Copy sizes Console Dry, electrostatic transfer system Sheets, bound documents Reversing automatic document feeder (RADF) Max. A6 (5-1/2" x 8-1/2") Image void: Max. 4 mm (5/32") (trailing edge) 52 copies/min. (A4, 8-1/2" x 11") 40 copies/min. (A4R (8-1/2" x 11"R)) 33 copies/min. (B4 (8-1/2" x 14")) 29 copies/min. Variable: 50 to 200% in 1% increments, total 151 steps Fixed presets: 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% (50%, 64%, 77%, 95%, 100%, 121%, 129%, 141%, 200%) Moving optical source, slit exposure (stationary platen) with automatic exposure function Three paper trays with automatic feed (500 sheets each) and one manual feed tray with 100-sheet automatic feed capability Heat rollers Magnetic brush development Halogen lamp Local voltage ±10% (For this copier's power supply requirements, see the name plate located on the right hand side, near the rear of the copier. ) Max. 1. 8 kW (when an optional sorter or staple sorter is installed) 1407 mm (W) x 660 mm (D) (55-13/32" (W) x 25-63/64" (D)) Approx. 141. 5 kg (312 lbs. ) Copying speed (at 100% copy ratio) Continuous copy First-copy time Warm-up time Copy ratio Exposure system Copy paper feed GENERAL INFORMATION Specifications Fusing system Developer system Light source Required power supply Power consumption Overall dimensions Weight 72 SPECIFICATIONS Copier dimensions 750 mm (W) x 660 mm (D) x 1365 mm (H) (29-17/32" (W) x 25-63/64" (D) x 53-3/4" (H)) Temperature: 15°C to 30°C (59°F to 86°F) Humidity: 20% to 85% 20-bin sorter (SF-S16) 20-bin staple sorter (SF-S53N) 20-bin staple sorter (SF-S55N) Large capacity tray (SF-C52/SF-C52N) Card counter (SF-EA11) Auditor (SF-EA12) Counter commander (SF-EA13) Personal counter (SF-71A/71B) Exit tray (sold separately in some regions) Operating conditions Optional equipment REVERSING AUTOMATIC DOCUMENT FEEDER Acceptable originals Weight: One-sided originals: 50 to 128 g/m2 (14 to 34 lbs. ) Two-sided originals: 50 to 128 g/m2 (14 to 34 lbs. ) for A5 and A4 (5-1/2" x 8-1/2" and 8-1/2" x 11") originals. 50 to 110 g/m2 (14 to 29 lbs. ) for B4 and A3 (8-1/2" x 14" and 11" x 17") originals. Size: A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") Capacity: Up to 50 sheets for A5, A4, and B4 (5-1/2" x 8-1/2", 8-1/2" x 11", and 8-1/2" x 14") originals provided the total aggregate thickness does not exceed 6. 5 mm or 1/4" (50 to 80 g/m2 or 14 to 21 lbs. ) or 5 mm or 3/16" (80 to 128 g/m2 or 21 to 34 lbs. ) Up to 30 sheets for A3 (11" x 17") originals In some regions, the reversing automatic document feeder is provided as optional equipment. GENERAL INFORMATION DUPLEX TRAY Paper type Number of copies Copy paper size Ordinary paper only 50 A5, A4, A4R, B4, A3, 8-1/2" x 11" (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", 11" x 17", A4) In some regions, 8-1/2" x 11" is indicated as 216 mm x 279 mm and/or 216 mm x 330 mm (8-1/2" x 13") size paper can be used additionally. ) Leading edge: Max. 4 mm (5/32") 56 to 80 g/m2 (15 lbs. to 21 lbs. ) Specifications Image void Copy paper weight Specifications are subject to change for improvement without notice. 73 MEMO GENERAL INFORMATION 74 OPTIONAL EQUIPMENT CONTENTS q q Page q q SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If "NO" is selected, external operators must enter the key operator code to access the key operator programs. (The factory default setting is "NO". ) Key operator programs 126 KEY OPERATOR PROGRAMS P90 Display the List of All P Codes Program P90 is used to sequentially display all programs. The programs in which the setting has been changed from the factory default setting are indicated with q. When P90 is entered, the following message will appear. [. . . ]