User manual SHARP UX-75

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. [. . . ] (Press before the sender presses their Start key. ) · When RECEIVING appears in the display, hang up. Answering on an extension phone connected to the same line 1 Answer the extension phone when it rings. 2 If you hear a soft fax tone, wait until your fax responds (you will hear pronounced, high-pitched tones), then hang up. Beep Pronounced, high-pitched tones 80 Optional Reception Settings 3 If the fax doesn't respond, or if the other party first talks to you and then twice on the extension 5 once and phone (only on a tone dial phone). This signals the fax to begin reception. wants to send a fax, press · The above step is necessary if you have set the Fax Signal Receive setting to NO. · Your fax will not accept the signal to begin reception ( 5 document is loaded in its feeder. ) if a Putting a call on hold HOLD . To put the other party on hold during a phone conversation, press When this is done, they cannot hear you. You can put the handset back in the cradle without breaking the connection. When you are ready to speak with the other party again, pick up the handset. If you did not put the handset back in the cradle, press HOLD again to resume conversation. Optional Reception Settings Fax Signal Receive Your fax will automatically begin reception if you hear a soft fax tone after answering a call on your fax or an extension phone. If you use a computer fax modem to send documents on the same line, you must turn this function off in order to prevent your fax from mistakenly attempting to receive documents from the computer fax modem. Follow the steps below to change the setting. 1 2 Press FUNCTION once and 3 times. Display: OPTION SETTING Press once and 6 times. FAX SIGNAL RX 81 4. Receiving Faxes Optional Reception Settings 3 4 Press once. 1=YES, 2=NO Press 1 to turn on the function, or The display briefly shows your selection, then: 2 to turn it off. POLLING 5 Press STOP to return to the date and time display. Changing the number for remote fax activation If desired, you can use a number other than 5 to activate fax reception from an extension telephone. You can select any number from 0 to 9. 1 2 3 4 Press FUNCTION once and 3 times. Display: OPTION SETTING Press once and twice. FAX REMOTE # Press once. ENTER (0-9) (5) Enter the desired number (any number from 0 to 9). The initial setting is YES (cut off the remainder). To change the setting, follow the steps below. 1 2 3 4 Press FUNCTION once and twice. Display: PRINT SET-UP Press once and twice. COPY CUT-OFF Press once. 1=YES, 2=NO Press 1 to set copy cut-off to YES (the remaining part of the document will not be printed), or The display briefly shows your selection, then: 2 to set copy INK SAVE MODE cut-off to NO (the remaining part will be printed on a second page). 5 86 Press STOP to return to the date and time display. 6. Special Functions Caller ID (Requires Subscription to Service) If you subscribe to a caller identification service from your telephone company, you can have the fax machine display the name and number of the caller when you receive a call. Important: To use this function, you must subscribe to a caller identification service from your telephone company. Note that your fax may not be compatible with some caller identification services. Area Code mode: This step is needed if your telephone exchange cannot dial a local phone number (within your calling area code) when the area code is dialed with the phone number (see Step 5). 1 2 3 4 Display: Press FUNCTION once and 3 times. OPTION SETTING Press once and 5 times. CALLER-ID Press once. 1=YES, 2=NO Press 1 (YES) to turn on Caller ID. and go AREA CODE # MODE to Step 8. ) 1=SET, 2=CLEAR 5 1 to select SET. (To clear a previously set area code, press Press ENTER AREA CODE 2 and go to Step 8. ) Note: Entering your area code in this step causes it to be automatically removed from local numbers in the Caller ID list (page 89). This is only required if you need to eliminate dialing of the area code when dialing a local number from the list. Example (using the area code "123"): If Step 5 is skipped, the Caller ID display will show 123-444-1234, and the number that will dial from the Caller ID list is 123444-1234. If the area code 123 is entered in Step 5, the Caller ID display will show 444-1234, and the number that will dial from the Caller ID list is 444-1234. 87 6. Special Functions (To turn off Caller ID, press 2 Caller ID (Requires Subscription to Service) 6 7 8 Enter the three digits of your area code. Press START/ MEMORY AUTO PRINT OUT to store your area code. Press STOP to return to the date and time display. How Caller ID operates When you receive a call, the name and phone number of the caller will appear in the display, beginning just before the second ring. [. . . ] Introduzca el número de telefax y pulse START/ MEMORY . . Grabacion de un mensaje de bienvenida 1. Introduzca un nombre pulsando las teclas numéricas. (Para introducir dos letras sucesivas que requieran la misma tecla, pulse SPACE = G= H= I= J= K= L= M= N= O= P= Q= R= S= T= , tecla de flecha después de U= V= W= X= Y= Z= introducir la primera letra). A= B= 2. Levante el auricular, oprima la tecla START/ MEMORY y hable en el microteléfono. [. . . ]