User manual SHARP VC-M25/45GM

[. . . ] Richten Sie sich nach den geltenden Gesetzen Ihres Landes. Dieses Handbuch darf weder ganz noch teilweise reproduziert, gespeichert oder in anderer Form übertragen werden, wenn nicht die vorherige Zustimmung von SHARP ELECTRONICS (EUROPA) GmbH vorliegt. ® ist ein eingetragenes Warenzeichen der Gemstar Development Corporation. Das -System wurde hergestellt unter der Lizenze der Gemstar Development Corporation gefertigt. [. . . ] Or: enter the recording date using the [ / ] or the NUMBER BUTTONS. Enter two digits for the day, then two for the month. For example for July 9th, press 0 9 (9th), then 0 7 (July). T I ME R MOD E SE T UP SET : SE L ECT : ENT ER ME NU : E X I T 1/2 DA T E 21 / 06 9 / 07 --/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP * ------- 5. If you want to make additional recordings at the same time each day or week, use [ / ] or select D (daily) or W (weekly). Then press SET to confirm. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D - -:--:---/-- --:--:---/-- --:--:-SP * ------- 7. Enter the channel using the [ / ] or the NUMBER BUTTONS. For example to record a programme on channel 3, press 0 3. Then press SET to confirm. GB-13 TINS-3775UMZZ ENGLISH. book Page 14 Monday, March 13, 2000 11:31 AM BASIC OPERATION HOW TO SET A DELAYED RECORDING 8. Enter the start time using the [ / ] or the 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-SP * SP * ----- NUMBER BUTTONS hours first then minutes (when entering less than 10 minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Enter the stop time, for example for 22:30 stop, press 2 2 3 0. 10. If your VCR has long play facility and you wish to change the RECORDING SPEED, use the [ / ] to highlight SP. Follow steps 1 to 4 of CHECKING A RECORDING. 2. If you wish to cancel a delayed recording, press [ / ] to highlight the recording to be cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP * --/-- --:--:-- ----/-- --:--:-- ----/-- --:--:-- --- 3. Press MENU. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER POWERSAVE OR TIMER STAND-BY mode. GB-15 TINS-3775UMZZ ENGLISH. book Page 16 Monday, March 13, 2000 11:31 AM ADVANCED OPERATION AUDIO AND YOUR VCR (Hi-Fi VCR'S ONLY) HI-FI STEREO SOUND (VC-MH76GM only) Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The VCR is normally set so that stereo sound is possible. The sound output from the VCR is controlled by the AUDIO OUT button on the remote control. If you wish to change the sound output you can use the AUDIO OUT button as follows: · Press AUDIO OUT once. The LEFT audio channel will be sent to BOTH speakers. The RIGHT audio channel will be sent to BOTH speakers. The MONO track will be sent to BOTH speakers. L and R will disappear from the VCR display. · Pressing AUDIO OUT a fourth time, normal Hi-Fi stereo sound will be heard. [. . . ] · Make sure the TV is set to the video channel. Playback picture is · Adjust the tracking using CHANNEL snowy. · The video heads may have been contaminated - refer to a SHARP Service Facility. Playback recording · Ensure the VCR is connected to a stereo TV does not playback in and SCART lead. [. . . ]