User manual SHARP VC-M31GM/M51GM

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH. ® and PlusCode ® are registered trademarks of Gemstar Development G Corporation. G system is manufactured under license from Gemstar Development Corporation. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) VCR REMOTE CONTROL 14. RECORD (The STOP button is also used to switch on the VCR. ) / 1. TIMER ON/OFF 5. AUDIO OUT (This button has no function with the VC-M303LM) / 6. TV/VCR /+ VCR FRONT PANEL/REMOTE CONTROL EQUIVALENT FUNCTIONS. [. . . ] When you have completed entering timer 12. Ensure that the tape on which you wish to record is inserted into the VCR, then press TIMER ON/OFF once to place the VCR in TIMER STANDBY mode. will be shown on the display. NOTES: · · · If flashes a video tape has not been inserted into the VCR. If the video tape is ejected when the VCR tries to record the record protection tab has been removed. During recording, press STOP ( ) to cancel the recording. If there are further recordings to be made, the VCR will return to TIMER STANDBY. If problems persist contact the SHARP Helpline on tel: 0990-274277 17 BASIC OPERATION HOW TO CHECK, CHANGE AND CANCEL A DELAYED RECORDING Before you start! · If appears on the VCR display, press TIMER ON/OFF to remove the symbol. CHECKING A RECORDING 1. · All the delayed recordings in the VCR's memory will be shown. SET MENU SCREEN T I ME R MOD E SE T UP 4. If the settings are correct press MENU to exit. · If you wish to change or cancel any settings, follow the procedures below. : SE L ECT : ENT ER ME NU : E X I T CHANGING A RECORDING 1. Follow steps 1 to 3 of CHECKING A RECORDING. 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 2. To change a delayed recording, press [ / ] to highlight the recording, then press SET to select. 3. Press [ / ] to highlight the setting to be changed and correct it by using the [ / or the NUMBER BUTTONS. confirm, then press MENU to exit. ] 4. If the poor quality is for a long period the VCR will automatically select the mono track and the sound will be in mono. NICAM sound may not be stereo. If problems persist contact the SHARP Helpline on tel: 0990-274277 19 ADVANCED OPERATION AUDIO AND YOUR VCR (VC-MH703HM/VC-MH713LM) CONNECTING TO AUDIO EQUIPMENT The diagram below shows how to connect your VCR to audio equipment. When connected in this way stereo sound is possible from the speakers. EXISTING AERIAL CABLE BACK OF TELEVISION RF CONNECTION CABLE ANTENNA IN ENTREE RF OUT SORTIE ANTENNE AERIAL IN RF-OUT AUDIO OUT L and R AUDIO PHONO LEADS (NOT SUPPLIED) + AMPLIFIER If problems persist contact the SHARP Helpline on tel: 0990-274277 20 ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape will wind forward and then return to its original position. The tape remaining will be shown on the VCR display in hours and minutes. By pressing the TAPE SPEED button on the remote control the remaining time will change between long play and standard play. For example, in standard play 1 hour 23 minutes is left on the tape: Pr in long play 2 hour 46 minutes is left on the tape: Pr NOTES: · · If tape remaining function is interrupted, the remaining time will not be displayed. [. . . ] Proof of purchase must be provided. 4. The guarantee does not cover carriage costs, batteries or video tapes. In the unlikely event of this product requiring repair, please contact the supplier from whom it was purchased. Where this is not possible, please contact the SHARP Helpline on the telephone number given below. 6. [. . . ]