User manual SHARP VC-781S

[. . . ] 5 Auto Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BASIC OPERATION Scart lead connection (not supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Important notes on your VCR and video tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 How to playback a video tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the video tape is ejected when the VCR tries to record the record protection tab has been removed. During recording, press STOP ( ) to cancel the recording. If there are further recordings to be made, the VCR will return to TIMER POWERSAVE OR TIMER STAND-BY. · · · GB-18 BASIC OPERATION HOW TO SET A DELAYED RECORDING CHECKING, CHANGING AND CANCELLING A RECORDING CHECKING A RECORDING MENU SCREEN T I ME R MOD E SE T UP 1. If in TIMER STANDBY mode, press TIMER ON/OFF to exit. 2. · · All the delayed recordings in the VCR's memory will be shown. You can check the settings and change or cancel them. SET : SE L ECT : ENT ER ME NU : E X I T CHANGING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP * ------- 2. If you wish to change a delayed recording, press [ / ] to highlight the recording, then press SET. 3. Press [ / ] to highlight the setting to be changed and correct it by using the[ / or the NUMBER BUTTONS. When all corrections are complete press SET, CANCELLING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 2. In this case the VCR automatically switches to receive the mono signal. NICAM sound may not be stereo. GB-20 ADVANCED OPERATION AUDIO AND YOUR VCR CONNECTING TO AUDIO EQUIPMENT The diagram below shows how to connect your VCR to audio equipment. When connected in this way stereo sound is possible from the speakers. EXISTING AERIAL CABLE BACK OF TELEVISION RF CONNECTION CABLE S-VIDEO CABLE ANTENNA IN ENTREE ANTENNE AERIAL IN G D S-VIDEO OUT SORTIE SON S-VIDEO RF OUT SORTIE ANTENNE AUDIO OUT L and R AUDIO PHONO LEADS (NOT SUPPLIED) RF-OUT + AMPLIFIER GB-21 ADVANCED OPERATION AUDIO DUBBING RECORDING SOUND ON TO A VIDEO TAPE (AUDIO DUBBING) This feature enables you to add narration or background music to a pre-recorded tape. · The audio signal will be recorded on the mono track. The Hi-Fi track will remain unchanged: Connect your audio equipment to AUDIO IN L-R terminals on the front of your VCR. If a microphone is to be used, connect it to your audio equipment. + AUDIO SOURCE 1. Connect the audio source to the AUDIO IN L-R terminals on the front of the VCR as shown above. 2. Insert the pre-recorded tape into the VCR. 3. Press PLAY/X2 ( recording. ) to view the 4. If you wish to listen to the original Hi-Fi track while you are recording the new dubbed audio track you will need to set AUDIO MIX to ON in the MODE menu. II A. Press PAUSE/STILL ( ) when you reach the point on the tape where you want audio dubbing to start. SP 6. Press A. DUB (A. DUB will be shown on your TV). NOTE: The input source will be automatically changed to L3 (Front phono jacks). 7. [. . . ] · Make sure the tape is not at the start. GB-45 TROUBLESHOOTING TROUBLESHOOTING AREA REMOTE CONTROL PROBLEM The VCR can not be operated by remote control POSSIBLE CAUSE/CURE · Remote control is too far away from the main unit. · Point the remote control at the VCR. · Batteries are flat - replace both. · Batteries have not been inserted correctly. [. . . ]